MOX6/MOX8 Owner’s Manual
Control and Functions
15
edit the parameters commonly applied to all Elements, Parts
or Zones in the following modes: Voice Edit, Performance,
Song/Pattern Mixing Edit, Mixing Voice Edit and Master Edit.
S [PATTERN SECTION/PERFORMANCE
CONTROL] button
This button is available only in the Performance mode and
Pattern mode. In the Performance mode, turning on this button
will assign the following functions to the Number [1] – [16]
buttons.
In the Pattern mode, turning on this button will assign
Sections A – H to the Number [1] – [16] buttons.
T [TRACK] button
Turning this button on in the Song/Pattern mode enables the
Number [1] – [16] buttons for selecting corresponding Song/
Pattern Tracks.
[MUTE] button (page 38)
Turning this button on in Normal Voice Edit and Mixing Voice
Edit enables the Number [1] – [8] buttons for muting Voice
Elements (1 – 8). Turning this button on in the other modes
enables the Number [1] – [16] buttons for muting
Performance Parts (1 – 4), Song Tracks/Parts (1 – 16), and
Pattern Tracks/Parts (1 – 16).
[SOLO] button (page 38)
Turning this button on in Normal Voice Edit and Mixing Voice
Edit enables the Number [1] – [8] buttons for soloing a Voice
Element (1 – 8). Turning this button on in the other modes
enables the Number [1] – [16] buttons for soloing a
Performance Part (1 – 4), a Song Track/Part (1 – 16), and a
Pattern Track/Part (1 – 16).
NOTE The on/off status of buttons T – affects the Number [1] – [16]
buttons in different ways, depending on the currently selected
mode. Refer to the table below.
Number [1] – [16] buttons
Use of these buttons differs depending on the on/off status of the [PATTERN SECTION/PERFORMANCE CONTROL], [TRACK],
[MUTE] and [SOLO] buttons.
Functions of the Number [1] – [16] buttons
Number button
Function
[1] – [4] Selecting Performance Parts 1 – 4.
[5] – [8] Setting the Arpeggio Switch to on/off for
Performance Parts 1 – 4.
[9] – [12] Setting the mute status for Performance Parts 1 – 4.
[13] – [16]
Setting the Arpeggio Hold for Performance Parts 1 – 4.
S T
Mode
When the [PATTERN SECTION/
PERFORMANCE CONTROL]
button is turned on:
When the [TRACK] button
is turned on:
When the [MUTE]
button is turned on:
When the [SOLO]
button is turned
on:
When all the
buttons are
turned off:
Voice Play – Keyboard transmit channel
setting
– – Voice selection
Normal Voice
Edit
– Changes the Edit mode from
Common Edit to Element Edit
and Element selection ([1] –[8]).
Element Mute setting
([9] – [16])
Solo Element
selection ([9] – [16])
–
Drum Voice
Edit
– Changes the Edit mode from
Common Edit to Drum Key Edit
–––
Performance
Play
Performance Control (S) Keyboard transmit channel
setting
Part Mute setting
([1] – [4])
Solo Part selection
([1] – [4])
Performance
selection
Performance
Edit
Performance Control (S) Performance Part selection
([1] – [4])
Part Mute setting
([1] – [4])
Solo Part selection
([1] – [4])
–
Master Play –
Keyboard transmit channel setting
(when memorizing the Voice mode
or Performance mode to the
current Master) or Song/Pattern
Track selection (when memorizing
the Song mode or Pattern mode to
the current Master)
– – Master program
selection
Master Edit – Changes the Edit mode from
Common Edit to Zone Edit and
Zone selection ([1] – [8])
–––
Song/Pattern
Play
Section selection in the
Pattern mode
Song/Pattern Track selection Song/Pattern Track
Mute setting
Solo Track selection Song/Pattern
selection
Song/Pattern
Mixing
Section selection in the
Pattern mode
Song/Pattern Part selection Song/Pattern Part Mute
setting
Solo Part selection Voice selection of
the current Part
Mixing Voice
Edit
– Element selection ([1] – [8]) Element Mute setting
([9] – [16])
Solo Element
selection ([9] – [16])
–
To Next Page
Loading...
Need help?
General
