To Next PageTo Next PageWhy is bass reproduction poor on my Yamaha RX-V350 Receiver?
If you're experiencing poor bass reproduction with your Yamaha Receiver, and “SOUND 1D BASS” on the set menu is set to SWFR or BOTH but your system doesn't have a subwoofer, select FRONT. Also, if the speaker mode settings on the set menu don't match your speaker configuration, select the appropriate position for each speaker based on their size.
What to do if the sound suddenly goes off on my Yamaha Receiver?
If the sound on your Yamaha Receiver suddenly cuts out, it could be due to a few reasons. The protection circuitry might have been activated because of a short circuit. Check that the speaker wires are not touching each other, and then turn the unit back on. Alternatively, the sleep timer might have turned the unit off. In this case, turn the power back on and play the source again. Finally, ensure the sound isn't muted by pressing the MUTE button.
How to fix Yamaha RX-V350 remote control that is not working?
If your Yamaha Receiver's remote control isn't working properly, consider these potential solutions. Ensure you are within a maximum range of 6 m (20 feet) and no more than 30 degrees off-axis from the front panel. Reposition the unit if direct sunlight or lighting is interfering with the remote control sensor. Replace all batteries if they are weak. Also, verify that the manufacture code has been set correctly, and try setting another code of the same manufacturer.
Why is there no sound from my Yamaha RX-V350?
If you're experiencing no sound from your Yamaha Receiver, start by checking all input and output cable connections to ensure they are properly connected; if the problem persists, the cables may be defective. Next, verify that you've selected the correct input source using INPUT l / h or 6CH INPUT (or the input selector buttons). Also, make sure the speaker connections are secure and that the proper front speakers are selected with SPEAKERS A/ B/OFF. Don't forget to check the volume level and ensure the unit isn't muted by pressing MUTE or any operation buttons. Finally, confirm that the source you're playing is compatible with the receiver.
Why does the remote control not work with my Yamaha RX-V350?
If the remote control for your Yamaha Receiver isn't working properly, make sure you're within a maximum range of 6 meters (20 feet) and no more than 30 degrees off-axis from the front panel. Also, reposition the unit if direct sunlight or lighting is striking the remote control sensor. Finally, replace all batteries if they are weak.
How to tune into the desired station on Yamaha RX-V350 Receiver?
If you cannot tune into the desired station with the automatic tuning method on your Yamaha Receiver, it may be because the signal is weak or the antenna connections are loose. Tighten the AM loop antenna connections and orient it for best reception.
How to stop a humming sound from my Yamaha RX-V350?
If you hear a humming sound from your Yamaha Receiver, it could be due to incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective.
Why is there no sound from the surround speakers on my Yamaha Receiver?
If you're not getting any sound from the surround speakers on your Yamaha Receiver, start by checking that the output level of the surround speakers isn't set to minimum. If it is, raise the output level. Also, if you're playing a monaural source with program 9, try selecting another sound field program.
What to do if Yamaha RX-V350 Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, there are several potential causes. First, ensure the power cord is securely connected. If that's not the issue, the protection circuitry might be activated; in this case, check all speaker wire connections to make sure they are secure and not touching anything else. Finally, if the unit has been exposed to a strong electric shock, try setting it to standby mode, disconnecting the power cord for 30 seconds, and then plugging it back in.
What does 'CHECK SP WIRES' mean on Yamaha RX-V350 Receiver?
If you see “CHECK SP WIRES” on the front panel display of your Yamaha Receiver, it indicates that the speaker cables are short-circuited. To fix this, make sure all speaker cables are connected correctly.
General| Channels | 5.1 |
|---|---|
| Dolby Digital | Yes |
| DTS | Yes |
| FM/AM Tuner | Yes |
| Impedance | 6 ohms |
| Type | AV Receiver |
| Input Sensitivity | 200 mV |
| Signal-To-Noise Ratio | 100 dB |
| Total Harmonic Distortion | 0.06% |
| Frequency Response | 10Hz - 100kHz |
| Amplifier Type | Discrete |
| Power Output | 100W per channel |
| Outputs | 1 x Audio, 1 x Video |
| Surround Sound Formats | Dolby Digital, Dolby Pro Logic II, DTS |
| Input Impedance | 47 kOhms |
| Audio Inputs/Outputs | RCA |
| Digital Audio Inputs | 2 (1 x Optical, 1 x Coaxial) |
| Video Inputs/Outputs | Composite |
Information for authorized service personnel.
Details and diagrams of the front panel.
Details and diagrams of the rear panel.
Details of remote control panels.
Technical specifications of the unit.
Views of the internal components and layout.
Procedures and options for self-diagnosis.
Step-by-step instructions for disassembly.
Procedure to check idling current.
Information on the unit's display data.
Data related to integrated circuits.
Information and diagrams of PCBs.
Diagrams of component pin connections.
Overall functional block diagram.
Detailed electrical schematic diagrams.
Comprehensive list of all parts.
Specific details on the remote control.
Tests related to Digital Signal Processing through modes.
Tests related to RAM data throughput.
Tests for Dolby Pro Logic audio processing.
Configuration tests for speaker settings.
Headphone output testing.
Tests for other input signal sources.
Tests for verifying the unit's display functionality.
Tests for manual audio output checks.
Functions for factory preset initialization.
Checks for analog data and fan operation.
Direct signal output without DSP.
YSS signal output with presence channel.
YSS signal output including head margin.
Digital full bit output for YSS signal.
RAM signal output with 0dB margin.
Dolby Pro Logic I processing mode.
Dolby Pro Logic II processing mode.
DTS Neo:6 audio processing (Not applied).
Front speaker setting for small units.
Setting for no center speaker.
LFE/Bass signal routing to front.
Presence speaker mix (5 channels).
Surround B power setting (Not applied).
Tone control set to flat.
Tone control +10dB boost.
Tone control -10dB cut.
Headphone test with 12dB margin.
Headphone test with 15dB margin.
Test for external decoder input.
Test for initial display and segments.
Noise output from all channels.
Noise output from Front L channel.
Noise output from Center channel.
Noise output from Front R channel.
Noise output from Surround R channel.
Surround B test (Not applied).
Noise output from Surround L channel.
Noise output from Sub Woofer channel.
Prevents RAM initialization, protects settings.
Reserves RAM initialization for factory settings.
Checks DC/PS protection values.
Checks temp and fan drive levels.
REC-OUT status (Not applied).
Checks impedance and power limiter.
Checks panel key inputs.
Shows digital input/output settings.
Displays reproduction signal frequency info.
Shows audio code mode info.
Displays reproduction signal format.
Shows signal processing status.
Checks YSS938 bus status.
Checks PLD/SRAM bus status.
Checks CS49329 messages.
Displays data version.
Displays TOC information.
Displays sum calculated value.
Selects PCB or SOFT mode.
Setting for model selection.
Selects tuner destination.
Selects tuner existence.
Selects RDS existence.
Selects ZONE2 existence.
Selects video format.
Shows software version details.
Displays checksum for program areas.
Shows port settings for microprocessor function.
Displays AAC function detection port state.
Confirms idling current across terminals.
Specific display data identifier.
Mapping of pin numbers to connections.
Assignment of pins to grid positions.
Data for the Main CPU IC.
Data for the Main CPU IC.
Pull-up resistance for key inputs.
Pin connection diagrams for ICs.
Visuals and types of diodes.
Visuals and types of transistors.
List of all electrical components.
