Why can I only hear the speaker on one side of my Yamaha RX-V496 Receiver?
If you only hear sound from one speaker with your Yamaha Receiver, check the cable connections to ensure they are correct. If the problem continues, the cables may be defective. Also, verify the BALANCE setting and adjust it to the appropriate position.
Why is there no sound from the center speaker on my Yamaha Receiver?
If there is no sound coming from the center speaker of your Yamaha Receiver, first check that the sound output level of the center speaker is not set to minimum and raise the level if needed. Then, verify that “CENTER SP” in the SET MENU is set to either the LRG or SML position, not NONE. Finally, ensure that you have selected the appropriate DSP program.
Why is there no sound and/or picture from my Yamaha Receiver?
If you're experiencing no sound or picture with your Yamaha Receiver, there could be several reasons: * Check your cable connections to ensure they are properly connected and not defective. * Make sure you've selected the correct input source using the INPUT SELECTOR or TAPE/MD MON / EXT. DECODER buttons. * Verify that your speaker connections are secure. * Confirm that SPEAKERS are set to the ON position for the speakers you're using. * Ensure the volume isn't muted by checking the VOLUME and MUTE settings. * If you're using a CD-ROM, confirm that the signals are compatible with the unit (PCM audio, Dolby Digital, or DTS).
What to do if the sound suddenly goes off on my Yamaha Receiver?
If the sound on your Yamaha Receiver suddenly cuts off, it could be due to the activation of the protection circuit because of a short circuit. Set the unit to standby mode and then turn it back on to reset the protection circuit. Another possibility is that the SLEEP timer has activated; turn the power on and play the source again.
Why is there no sound from the rear speakers on my Yamaha RX-V496 Receiver?
If there's no sound from the rear speakers connected to your Yamaha Receiver, first check that the output level of the rear speakers is not set to minimum and increase it if necessary. If you are playing a monaural source with the PRO LOGIC/Normal or PRO LOGIC/ENHANCED program, select another DSP program suitable for the monaural source.
Why is there no sound from the effect speakers on my Yamaha RX-V496 Receiver?
If there is no sound from the effect speakers on your Yamaha Receiver, make sure the sound effect is turned on by pressing the EFFECT button. If you're using a Dolby Surround, Dolby Digital, or DTS decoding DSP program with material not encoded with these formats, try selecting another DSP program.
Why is the volume level low when playing a record on my Yamaha RX-V496 Receiver?
If the volume level is low when playing a record on your Yamaha Receiver, and you are using a turntable with an MC cartridge, connect the turntable to the unit through the MC head amplifier.
How to stop a humming sound from my Yamaha RX-V496 Receiver?
If you hear a humming sound from your Yamaha Receiver, ensure the audio plugs are firmly connected; if the problem persists, the cables may be defective. Also, if using a turntable, make sure it is properly connected to the GND terminal on the unit.
What to do if my Yamaha RX-V496 does not work normally?
If your Yamaha Receiver isn't working normally, the internal microcomputer may have frozen due to an external electric shock or a power supply with low voltage. To resolve this, set the unit to standby mode, disconnect the AC power cord from the outlet, wait about 30 seconds, then reconnect the power and try operating the unit again.
How to fix Yamaha Receiver that won't turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, check the power cord to ensure it is firmly connected. Also, when the unit is in standby mode, make sure the IMPEDANCE SELECTOR switch on the rear panel is fully set to either the right or left position.
General| Type | AV Receiver |
|---|---|
| Channels | 5.1 |
| Amplifier Type | Discrete |
| Input Sensitivity | 200 mV (line) |
| Weight | 9.8 kg |
| Tuner Section | FM/AM |
| Preset Stations | 40 |
| Surround Sound Formats | Dolby Digital, Dolby Pro Logic |
| Frequency Response | 10 - 100000 Hz |
| Total Harmonic Distortion | 0.06 % |
| Input Sensitivity/Impedance | 200 mV / 47 kΩ |
| Dimensions | 151 mm |
| Signal-to-Noise Ratio | 96dB (line) |
To Next Page
