What causes continuous crackling and hissing noises in Yamaha RX-V630 Receiver?
Continuous crackling and hissing noises in your Yamaha Receiver can be due to noises resulting from lightning, fluorescent lamps, motors, thermostats and other electrical equipment. Try using an outdoor antenna and a ground wire to help reduce the noise, but it is difficult to eliminate all noise.
What to do if Yamaha Receiver volume level cannot be increased or sound is distorted?
If the volume level on your Yamaha Receiver cannot be increased or the sound is distorted, check if the component connected to the OUT (REC) jacks of this unit is turned off. If so, turn on the power to the component.
What causes buzzing and whining noises in Yamaha RX-V630?
Buzzing and whining noises, especially in the evening, with your Yamaha Receiver can be caused by a TV set being used nearby. Try moving the unit away from the TV.
How to fix a 'humming' sound in Yamaha RX-V630?
If you're hearing a humming sound from your Yamaha Receiver, firmly connect the audio plugs. If the problem persists, the cables may be defective.
How to fix Yamaha RX-V630 when desired station cannot be tuned in with the automatic tuning method?
To resolve the issue of not being able to tune into a desired station with the automatic tuning method on your Yamaha Receiver, tighten the AM loop antenna connections and orient it for best reception if the signal is weak or the antenna connections are loose.
What causes noise interference from digital equipment in Yamaha RX-V630 Receiver?
If you're experiencing noise interference from digital or high-frequency equipment with your Yamaha Receiver, it may be because the unit is too close to the digital or high-frequency equipment. Move the unit further away from such equipment.
General| Type | AV Receiver |
|---|---|
| Channels | 6.1 |
| THD | 0.06% |
| Input Sensitivity | 200 mV |
| Signal to Noise Ratio | 100 dB |
| Digital Sound Processor (DSP) | Yes |
| Input Impedance | 47 kOhms |
| Output Level | 1 V |
| Input Type | RCA, Optical, Coaxial |
| Surround Sound | Dolby Digital, DTS |
| Preset Stations | 40 |
| Tuning Range | FM/AM |
| Output Type | Speaker |
| Audio Outputs | 2 |
| Digital Audio Inputs | 1 Optical, 1 Coaxial |
| Video Inputs | Composite: x4, S-Video: x4, Component: x2 |
Explains graphical symbols and initial safety warnings to reduce shock risk.
Provides comprehensive safety guidelines for operating the unit, cleaning, and handling accessories.
Details precautions for replacement parts, servicing, mounting, heat, and CATV grounding.
Provides guidelines for grounding outdoor antennas to protect against surges and static charges.
Explains FCC compliance, modification warnings, and measures to resolve interference issues.
Important safety and operational guidelines to follow before using the unit for the first time.
Details the unit's power output, Dolby, DTS, and CINEMA DSP capabilities.
Lists tuner capabilities and additional features like D/A converter and test tone generator.
Provides information on manual conventions, button naming, and printing.
Lists all items included in the product package for verification.
Step-by-step guide for installing batteries in the remote and important notes on battery usage.
Identifies and explains the function of each button and display on the unit's front panel.
Explains additional front panel controls for audio settings, tuning, and video input.
Explains the infrared window, code setting, and input selector buttons.
Details buttons for volume, mute, power, sleep timer, and DSP control.
Explains how to switch between stereo and DSP effects and enter the SET MENU mode.
Provides guidance on proper remote control operation, range, and handling precautions.
Explains indicators for processor status and input source selection.
Details indicators for mute, volume, PCM, silent, headphones, and DSP programs.
Explains multi-information display and indicators for tuning, memory, auto mode, sleep, and input channels.
Provides diagrams and instructions for optimal placement of all speaker types.
Explains how a subwoofer expands the sound field and its benefits for bass frequencies.
Details how to prepare and connect speaker cables to the unit's terminals.
Identifies the different speaker terminals available for connection (Main, Rear, Center).
Illustrates speaker wiring and explains the function of the subwoofer input jack.
Details how to set the impedance selector switch based on speaker impedance for safe operation.
Introduces the connection process and lists various input/output jack categories.
Explains how to connect digital audio sources and general audio components.
Details the process of connecting various video sources like composite, S-Video, and component.
Illustrates typical video connections between components and the unit.
Details how to connect CD players and CD recorders/MD recorders via digital or analog jacks.
Provides instructions for connecting AM loop and FM indoor antennas for signal reception.
Explains how to connect an external amplifier to the unit's output jacks for increased power.
Details how to connect external decoders or processors using the 6CH INPUT jacks.
Instructions for connecting the unit's AC power cord and details on switched AC outlets.
Explains the voltage selector switch and the procedure for the first power-on.
Steps to turn on the unit and video monitor after all connections are complete.
Summarizes the available SPEAKER SET items (1A-1F) and their default configurations.
Explains how to use the test tone to balance speaker output levels at the listening position.
Details how to adjust output levels for center, rear, and subwoofer using volume controls.
Guides on selecting the input source and activating the main speaker sets for playback.
Explains how to select the 6CH INPUT for audio sources, noting limitations.
Covers adjusting volume, using BASS/TREBLE, and selecting DSP programs for enhanced sound.
Details the BGV function for enjoying video with audio and how to mute/unmute the sound.
Instructions on how to put the unit into standby mode when playback is finished.
Explains how to select input modes (AUTO, DTS, ANALOG) and their behavior with digital signals.
Provides notes on 96-kHz sampling digital signals and playing DTS-CD/LDs.
Guides on selecting DSP programs and sub-programs for enhanced listening experiences.
Includes notes on DSP program availability, usage with 6CH INPUT, and source-dependent selection.
Details how to select PRO LOGIC II for 2-channel sources and choose between Movie and Music modes.
Explains how to activate the Dolby Digital EX/DTS-ES decoder and its matrix modes.
Describes how to achieve virtual surround effects without rear speakers using DSP.
Explains how to enjoy DSP sound fields with headphones using SILENT CINEMA DSP.
Guides on turning off sound effects for normal stereo listening and its implications.
Defines sound fields and explains how YAMAHA DSP recreates acoustic environments.
Lists and describes Hi-Fi DSP programs like CONCERT HALL, JAZZ CLUB, and ROCK CONCERT.
Details how CINEMA-DSP enhances movie soundtracks by integrating Dolby and DTS technologies.
Explains MOVIE THEATER programs that recreate cinema-quality sound and localization.
Details Dolby Pro Logic II's 5-channel playback for movie and music sources.
Lists CINEMA-DSP program names categorized by input format (Stereo, Dolby Digital, DTS).
Provides descriptions for MOVIE THEATER programs and audio-video programs like GAME and SPORTS.
Explains automatic and manual tuning procedures for finding radio stations.
Guides on automatically storing FM stations with strong signals into memory.
Details options for selecting preset numbers and tuning direction for manual storage.
Explains how the unit retains stored station data even after power loss.
Details the process for manually storing up to 40 radio stations.
Guides on selecting stored stations using preset numbers and groups.
Explains how to swap the assignments of two stored radio stations.
Step-by-step instructions for setting the sleep timer to automatically turn off the unit.
Explains how to cancel the sleep timer function by pressing the SLEEP OFF option.
Covers general recording steps and special considerations for DTS software.
Explains timer operations and the unit's memory back-up feature.
Guides on navigating and adjusting various settings within the SET MENU using the remote control.
Explains how to select speaker modes (CENTER, MAIN, REAR) for optimal sound configuration.
Details settings for rear speakers, rear center, and LFE/bass output modes.
Explains settings for main speaker level, LFE level, and speaker delay time adjustment.
Details settings for dynamic range, left/right balance, and headphone tone control.
Covers input/output assignments, input modes, display settings, and memory guard.
Details how to adjust output levels for effect speakers using the remote control.
Explains how to adjust the delay time for center and rear center speakers for better sound localization.
Guides on adjusting PRO LOGIC II Music parameters like Panorama and Dimension.
Addresses unit startup, no sound, picture issues, and sound muting.
Solves problems with sound cutting off, one-sided audio, and effect speaker sound.
Addresses FM stereo noise, distortion, tuning problems, and preset station issues.
Solves problems related to remote control functionality, distance, and battery issues.
Defines audio terms like Dolby Surround, Dolby Digital, DTS, and LFE.
Defines Virtual CINEMA DSP, PCM, S-video, and Component video signals.
Lists detailed technical specifications for audio output, FM, and AM tuner performance.
Details general specifications, video signal types, dimensions, weight, and included accessories.
To Next Page
