Yanmar 3GMD - Page 140

134
CHAPTER SIX
Table 2 ENGINE SPECIFICATIONS (3GM AND 3GM30) (continued)
71.913-71.943mm (2.8312-2.8324 In.)
71.850 mm (2.8287 In.)
19.995-20.008mm (0.7872-0.7877In.)
20.000 mm (0.7874 In.)
0.065-0.100 mm (0.0026-0.0039In.)
0.035-0.070 mm (0.0014-0.0028In.)
0.020-0.055mm (0.0008-0.0022In.)
0.20-0.40 mm (0.008-0.016 In.)
19.991-20.000mm (0.7870-0.7874 In.)
74.910-74.940mm (2.9492-2.9504 In.)
74.850 mm (2.9468 In.)
0.68-0.88 mm (0.027-0.035 In.)
0.025-0.047mm (0.0010-0.0019 ln.)
0.005 mm tlght-0.017 mm loose
(0.0002 In. tlght-0.0007 In. loose)
0.036-0.092 mm (0.0014-0.0036In.)
0.036-0.092 mm (0.0014-0.0036In.)
0.036-0.095 mm
(0.0014-0.0037In.)
39.950-39.964mm (1.5728-1.5734 In.)
0.01 mm (0.0004 In.)
24.63 mm (0.970 In.)
0.028-0.086 mm (0.0011-0.0034In.)
0.2-0.4 mm (0.008-0.016 In.)
0.07 mm (0.003 In.)
1.97-1.99 mm (0.0776-0.0783In.)
3.97-3.99 mm (0.1563-0.1571 In.)
35.000 mm (1.3780 In.)
33.000 mm (1.2992 In.)
43.950-43.964 mm (1.7303-1.7309 in.)
43.950-43.964mm (1.7303-1.7309In.)
59.950-59.964mm (2.3602-2.3608 In.)
0.01 mm (0.0004 In.)
0.09-0.19 mm (0.0035-0.0075 In.)
0.15 mm (0.006 In.)
Mechanical
10.000 mm (0.3937 in.)
9.95 mm (0.3917 in.)
0.010-0.040 mm (0.0004-0.0016In.)
0.10 mm (0.004 In.)
45° .
45°
(continUed)
30.000 mm (1.1811
ln.)
41.500 mm (1.6339 In.)
0.02 mm max. (0.0008 In. max.)
0.05-0.13 mm (0.002-0.005 In.)
0.3 mm (0.012 In.)
0.03 mm (0.0012 in.)
Cylinder
block warpage-max. 0.05 mm (0.002 In.)
Piston diameter
3GM
Standard
Wear limit
3GM30
Standard
Wear limit
Piston
top clearance
Piston ring side clearance
Top ring
Second ring
Piston ring side clearance (continued)
Oil ring
Ring end gap (all rings)
Piston pin diameter
Piston pin hole diameter
In piston
In rod
Piston pin clearance
In rod
In piston
Piston ring width
Top and second ring
Oil control ring
Crankshaft main journal diameter
Timing gear end
Center
Flywheel end
Journal
out-of-round-max.
Crankshaft end play
Crankshaft runout-max.
Main bearing clearance
Timing gear end
Center
Flywheel end
Crankpln diameter
Journal
out-of-round-max.
Intermediate thrust bearing width-min.
Crankpin bearing clearance
Connecting rod side clearance
Cylinder head warpage-max.
Camshaft
Valve lobe 11ft
Fuel pump lobe 11ft
Journal diameter
End journal
Center journal
Runout
Timing gear backlash
Maximum allowable
Push rod
runout-max.
Valve lifter
Type
Outside diameter
Outside
diameter-min.
Clearance in block
Max. clearance
Valve face angle
Valve seat angle