8-8
8. OPERATE THE TRACTOR
Lx410/450/490 Operator's Manual
(A) Primary gear lever
(B) Forward/N/reverse lever
(C) Clutch pedal
(D) Range gear lever
Speed ranges of the range gear lever
4. Use the primary gear lever to match the gear to
the power and speed requirements of the current
work.
Speed ranges of the primary gear lever
5. Increase the engine speed if more loads are
anticipated.
• A suitable (not excessive) load on the engine is
indicated when:
• the engine Revolutions Per Minute (rpm)
increase only slightly when the throttle control
lever is moved forward
6. To make the load engage smoothly, gradually
release the clutch pedal, for the following levers:
• Range gear lever
• Forward/N/reverse lever
• 2WD/4WD lever
Speed Range Applications
L
Work involving much power at low
speed, e.g., mowing tall grass,
positioning a backhoe, tilling hard
soil, etc.
M
Work involving a moderate level of
hauling; e.g., tilling, and grass
mowing.
H
Work involving high-speed
operation, e.g., light mowing and
transport.
v30_w_c5-P35-n2_IMG_4480
(A)
IMPORTANT
To prevent overloading the engine, always select
the appropriate gear and engine speed for the job.
● Use a higher gear and lower engine speed for
work involving a light load.
● Use a lower gear and higher engine speed for
work involving a heavy load.
Speed Range Applications
1
Work involving high power at low
speed.
2
Work involving a moderate power
and speed.
3
Work involving high speed and low
power.
4
Work involving higher speed and
lower power.
IMPORTANT
● Avoid premature clutch damage.
● Avoid depressing the clutch pedal while the
tractor is in motion.
㪫㫉㪸㫍㪼㫃㫀㫅㪾㩷㫊㫇㪼㪼㪻㩷㫎㫀㫋㪿㩷㪘㪞㩷㫋㫀㫉㪼㩿㪈㪋㪅㪐㪄㪉㪋㪀
㪉
㪊
㪈㪘㪏㪉㪌㪇㪄㪍㪌㪌㪍㪇
㪈
㪣
㪤
㪟
㪉㪅㪌
㪈㪇
㪈㪌
㪉㪇㪤㪧㪟
㪉㪅㪌 㪈㪇㪌㪈㪌㪉㪇㪉㪌
㪊㪇㫂㫄㪆㪿
㪥㫆㫋㪼
㪈㪅㪠㫅㪻㫌㫊㫋㫉㫀㪸㫃㩷㫋㫀㫉㪼㩿㪈㪎㪅㪌㪣㪄㪉㪋㪀㩷㫊㫇㪼㪼㪻㩷㫀㫊㩷㪊㩼㩷㫊㫃㫆㫎㪼㫉㩷㫋㪿㪸㫅㩷㪘㪞㩷㫋㫀㫉㪼㩿㪈㪋㪅㪐㪄㪉㪋㪀㪅
㪉㪅㪫㫌㫉㪽㩷㫋㫀㫉㪼㩿㪋㪋㪯㪈㪏㪅㪇㪇㪀㩷㫊㫇㪼㪼㪻㩷㫀㫊㩷㪈㪇㩼㩷㫊㫃㫆㫎㪼㫉㩷㫋㪿㪸㫅㩷㪘㪞㩷㫋㫀㫉㪼㩿㪈㪋㪅㪐㪄㪉㪋㪀㪅
㪊㪅㪩㪼㫍㪼㫉㫊㪼㩷㫊㫇㪼㪼㪻㩷㫀㫊㩷㪇㪅㪊㩼㩷㪪㪣㪦㪮㪜㪩㩷㫋㪿㪸㫅㩷㪽㫆㫉㫎㪸㫉㪻㩷㫊㫇㪼㪼㪻㪅
㪌
㪤㪠㪥
㪤㪘㪯
㪜㫅㪾㫀㫅㪼㩷㫊㫇㪼㪼㪻
㪧㪫㪦㩷㫊㫇㪼㪼㪻㩿㫉㫇㫄㪀
㪌㪋㪇
㪋
㪈
㪉
㪊
㪋
㪈
㪉
㪊
㪋
㪩㪸㫅㪾㪼 㪧㫉㫀㫄㪸㫉㫐
To Next Page
Loading...
