To Next Page

To Previous Page

t$POTJEFSUIFGPSDFBOEEJSFDUJPOPGUIFXJOEUIFMFBOBOECBMBODFPGUIFUSFFBOEUIF

MPDBUJPOPGMBSHFMJNCT5IFTFUIJOHTJOnVFODFUIFEJSFDUJPOJOXIJDIUIFUSFFXJMMGBMM%POPUUSZ

UPGFMMBUSFFBMPOHBMJOFEJGGFSFOUGSPNJUTOBUVSBMMJOFPGGBMM

t3FNPWFEJSUTUPOFTMPPTFCBSLOBJMTTUBQMFTBOEXJSFGSPNUIFUSFFXIFSFGFMMJOHDVUTBSF

UPCFNBEF

t/PUDIFE6OEFSDVU$VUBOPUDIBCPVUUIFEJBNFUFSPGUIFUSVOLJOUIFTJEFPGUIFUSFF

.BLFUIFOPUDIDVUTTPUIFZJOUFSTFDUBUBSJHIUBOHMFUPUIFMJOFPGGBMM5IJTOPUDITIPVMECF

DMFBOFEPVUUPMFBWFBTUSBJHIUMJOF5PLFFQUIFXFJHIUPGUIFXPPEPGGUIFTBXBMXBZTNBLF

UIFMPXFSDVUPGUIFOPUDICFGPSFUIFVQQFSDVU

t'FMMJOH#BDLDVU "TUIFGFMMJOHDVUHFUTDMPTFUPUIFIJOHFUIFUSFFTIPVMECFHJOUPGBMM*G

UIFSFJTBOZDIBODFUIFUSFFNBZOPUGBMMJOUIFEFTJSFEEJSFDUJPOPSJUNBZSPDLCBDLBOECJOE

UIFTBXDIBJOTUPQDVUUJOHCFGPSFUIFGFMMJOHDVUJTDPNQMFUFBOEVTFXFEHFTPGXPPEQMBTUJD

PSBMVNJOVNUPPQFOUIFDVUBOEESPQUIFUSFFBMPOHJUTEFTJSFEMJOFPGGBMM.BLFUIFCBDLDVU

MFWFMBOEIPSJ[POUBMBUMFBTUDNBCPWFUIFIPSJ[POUBMDVUPGUIFOPUDI

/05& /FWFSDVUUISPVHIUPUIFOPUDI"MXBZTMFBWFBCBOEPGXPPECFUXFFOUIFOPUDIBOE

CBDLDVUBQQSPYJNBUFMZDNPSUIFEJBNFUFSPGUIFUSFF5IJTJTDBMMFEiIJOHFwPS

iIJOHFXPPEw*UDPOUSPMTUIFGBMMPGUIFUSFFBOEQSFWFOUTTMJQQJOHPSUXJTUJOHPSTIPPUCBDLPG

UIFUSFFPGGUIFTUVNQ

t0OMBSHFEJBNFUFSUSFFTTUPQUIFCBDLDVUCFGPSFJUJTEFFQFOPVHIGPSUIFUSFFUPFJUIFSGBMM

PSTFUUMFCBDLPOUIFTUVNQ5IFOJOTFSUTPGUXPPEFOPSQMBTUJDXFEHFTJOUPUIFDVUTPUIFZEP

OPUUPVDIUIFDIBJO%SJWFXFEHFTJOMJUUMFCZMJUUMFUPIFMQKBDLUIFUSFFPWFS

t"TUSFFTUBSUTUPGBMMTUPQUIFDIBJOTBXBOEQVUJUEPXOJNNFEJBUFMZ3FUSFBUBMPOHUIF

DMFBSFEQBUICVUXBUDIUIFBDUJPOJODBTFTPNFUIJOHGBMMTZPVSXBZ

HINGE

2" (5 cm) OR 1/10 DIA

NOTCH -

APPROX. 1/3

DIA

M ETER OF

TRUNK

BACK CUT

2" (5 cm)

HINGE

BACK CUT

Fig. 13

.PEFM/P]$POUBDUVT

Operation

WARNING: Never cut through to the notch when making a back cut.

The hinge controls the fall of the tree. This is the section of wood

between the notch and backcut.

Yardworks 054-5703-0 Instruction Manual

Other manuals for Yardworks 054-5703-0