EasyManua.ls Logo

York BP 240 User Manual

York BP 240
36 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
036-21490-002-A-0204
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
TECHNICAL GUIDE
SUNLINE 2000™ - BP 180
SUNLINE MAGNUM™ - BP 240
SINGLE PACKAGE
HEAT PUMPS
ASHRAE 90.1 COMPLIANT
MODEL BP180 and BP240
15 and 20 NOMINAL TONS
9.9 EER (15 TON) and 10.3 EER (20 TON)
®
BP 180
BP 240
DESCRIPTION
York Sunline 2000™ BP 180 & Sunline Magnum™ BP 240
Heat Pumps are convertible single package units. All models
have dual refrigerant circuits for efficient part load operation.
Although the units are primarily designed for curb mounting
on a roof, they can also be slab-mounted at ground level or
set on steel beams above a finished roof.
These heat pumps utilize a unique ambient compensated
time-temperature defrost system. The defrost module auto-
matically increases the time interval between defrost cycles
as the outdoor ambient temperature decreases. This helps to
eliminate unnecessary and costly defrosts.
All units include:
Simplicity
™ Control Board
Powder Paint finish that meets ASTM-B-117 750 hour
salt spray standards
Two-stage cooling provided by dual independent refrig-
eration circuits with expansion valves, filter-driers, high
and low pressure/loss of charge switches and freez-
estats
Hermetically sealed compressors with crankcase heat-
ers
Permanently lubricated motors
Bottom or side air discharge configuration capability
(field convertible)
Belt Drive Blower Motor
Manufactured under the quality standards of ISO9001
Twenty-four volt control circuit with compressor lock-out
Zero-25% fixed air damper with hood
Copper tube/aluminum fin coils
Easy access to all components
Rigging holes in base rails for lifting
Single point power connection
Complete factory package - tested, charged and wired
Agency approvals on all units
WARRANTY
Factory Limited Parts Warranty
One-year parts warranty
A Five-year parts warranty on the compressor and
electric heat elements.
Question and Answer IconNeed help?

Do you have a question about the York BP 240 and is the answer not in the manual?

York BP 240 Specifications

General IconGeneral
Model NumberBP240
CategoryHeat Pump
Voltage208/230V
Phase1
RefrigerantR-410A

Summary

Product Nomenclature

Ratings and Performance Data

Unit Ratings

Presents cooling, heating, and electric heat ratings for the unit models.

Cooling Capacities - BP 180 (15 Ton)

Detailed cooling capacity data for the 15-ton BP 180 model under various conditions.

Cooling Capacities - BP 240 (20 Ton)

Detailed cooling capacity data for the 20-ton BP 240 model under various conditions.

Heating Capacities - 15 Ton

Presents heating capacity data for the 15-ton models at various outdoor temperatures.

Heating Capacities - 20 Ton

Presents heating capacity data for the 20-ton models at various outdoor temperatures.

Blower Performance - 15 Ton

Provides blower performance data for 15-ton units with bottom duct connections.

Blower Performance - 20 Ton

Provides blower performance data for 20-ton units with bottom duct connections.

Blower Motor and Drive Data

Details specifications for blower motors and drive configurations.

Electrical and Wiring Information

Voltage Limitations

Specifies the minimum and maximum voltage limitations for unit operation.

Electrical Data (Without Convenience Outlet)

Provides electrical data including compressor, motor, and heater options.

Electrical Data (With Convenience Outlet)

Provides electrical data with powered convenience outlet considerations.

Electric Heat Correction Factors

Correction factors for electric heat capacity based on nominal voltage.

Physical and Application Data

Physical Data

Details physical specifications of components like blowers, coils, and filters.

Unit Dimensions - 15 Ton

Illustrates the physical dimensions of the 15-ton unit.

Unit Dimensions - 20 Ton

Illustrates the physical dimensions of the 20-ton unit.

Guide Specifications

General Unit Specifications

Details unit manufacturing, construction, performance, and compliance with standards.

Unit Description

Specifies factory-assembled single package units, design features, and minimum EER ratings.

Related product manuals