York YCAQ10 - ISOLATOR MOUNTING; MASON INDUSTRIES MOUNTING LOCATIONS; VIBRATION MOUNTING AND CONTROLS MOUNTING; COMPRESSOR MOUNTING

8 YORK INTERNATIONAL
VIBRATION MOUNTING AND CONTROLS
ISOLATOR MOUNTING LOCATION
Installation Instructions
1. Identify manufacturer of isolator and locate at proper
mounting point using appropriate table below.
2. Block up equipment so as to install spring mount with
pin on top of housing into Equipment Mounting Holes.
3. Mounting Adjustment Nut is inside the isolator mount
located just below the top plate of the mount. Turn
nut 2 turns clockwise (down) to load spring mount at
each location.
4. Take two additional turns on Adjustment Nut of each
mount.
5. Repeat step No. 3 as many times as necessary to
bring height of isolator to proper height.
6. Take additional turns on mounts at low side or corner
to level the equipment.
Isolator Locations
Chiller
JKLMNPRS
Model No.
Type & Sizes
YCAQ10,R1 2-31 2-31 2-31 2-27 ––––
YCAM12,N13 1-31 1-32 2-28 1-32 1-31 2-28 2-28 1-31
YCAK14, L15 1-31 2-27 2-27 2-28 1-31 2-28 2-28 1-31
YCAI16, J17 1-32 2-31 2-28 2-32 1-31 2-31 2-28 1-31
YCAG18, H19 1-32 2-31 4-27 2-27 1-32 2-31 2-32 2-27
MOUNTING – ALUMINUM COIL UNITS
Isolator Locations
Chiller
JKLMNPRS
Model No.
Type & Sizes
YCAQ10,R1 2-32 2-32 2-27 2-31 ––––
YCAM12,N13 1-31 2-28 2-28 2-28 1-32 2-28 2-28 1-32
YCAK14, L15 2-27 2-28 2-28 2-31 2-27 2-31 1-32 2-27
YCAI16, J17 2-27 2-32 2-31 2-31 2-32 2-31 2-31 2-27
YCAG18, H19 2-27 2-32 4-28 2-31 2-28 2-32 4-27 2-28
MOUNTING – COPPER COIL UNITS
MASON INDUSTRIES
Isolator Locations
Chiller
JKLMNPRS
Model No.
Type & Sizes
YCAQ10,R1 406 403 403 404 ––––
YCAM12,N13 401 404 405 404 401 405 405 401
YCAK14, L15 401 402 402 403 401 405 406 404
YCAI16, J17 401 406 405 403 401 403 403 401
YCAG18, H19 404 403 407 405 404 405 407 402
MOUNTING – ALUMINUM COIL UNITS
Isolator Locations
Chiller
JKLMNPRS
Model No.
Type & Sizes
YCAQ10,R1 407 407 406 406 ––––
YCAM12,N13 404 405 403 405 404 405 405 404
YCAK14, L15 404 403 403 406 404 406 404 402
YCAI16, J17 402 407 406 406 402 407 406 402
YCAG18, H19 402 407 407 403 404 405 407 402
MOUNTING – COPPER COIL UNITS
COMPRESSOR MOUNTING
The compressor(s) are mounted on four (4) isolator pads
(one under each compressor foot). (See Fig. 3.) The
YCAQ10, R11 YCAM12, N13, K14, L15, I16, J17, G18, H19
mounting bolts are not to be loosened or adjusted at
installation.
LD01624