Zeiss opmi lumera 700 User Manual (English)

Other manuals for Zeiss opmi lumera 700

Questions and Answers:

I
iortizAug 18, 2025
Why is there no electrical function in my Zeiss Microscope?
- A
  Angela CarrAug 18, 2025
  If your Zeiss Microscope has no electrical function, there could be several reasons: * The power plug might not be properly connected. Ensure that the power plug is securely connected. * The stand power switch may not be switched on. Check if the power switch is illuminated green; if not, press the power switch. * The automatic circuit breaker in the stand power switch may be triggered. Try pressing the power switch. If it trips again, contact ZEISS Service. * There might be a power supply failure, in which case you should contact your in-house electrician.
E
esandersAug 20, 2025
How to fix faulty illumination on Zeiss surgical microscope?
- A
  Anita RyanAug 20, 2025
  If the illumination on your Zeiss surgical microscope is faulty, consider the following: * The brightness level might be set too low. Increase the brightness on the stand or the 14-function foot control panel. * The lamp may be aging, reducing the amount of light. You can switch halogen lamps or change the Superlux Eye light source lamp module. * The light guide might not be correctly inserted. Ensure that you push the light guide in as far as it will go. * The lamp reflector for the halogen lamp might not be sitting correctly in the lamp bulb. Press the lamp reflector into the lamp bulb.
J
Joseph BellAug 23, 2025
What to do if data cannot be saved on Zeiss opmi lumera 700?
- M
  Marvin WilliamsAug 23, 2025
  If you are unable to save data on your Zeiss Microscope, check the following: * The USB storage device may be defective. Ensure it is working correctly; if not, replace it. * The USB storage format might not be supported. Use USB storage devices with FAT32 or NTFS. * There may be insufficient storage capacity. Delete unnecessary data, and note the available storage space display. * There might be no network connection. Establish a network connection. * There might be no network authorization. Ensure the network and directories are shared, and adjust the read and write permissions.
M
millermariaAug 27, 2025
Why is my Zeiss Microscope 14-function foot control panel not working?
- J
  Julia JohnsonAug 28, 2025
  If your Zeiss Microscope's 14-function foot control panel is not functioning, here are some things to check: * The batteries may be dead. Replace the batteries. * If using rechargeable batteries, they may be dead. Replace the rechargeable batteries. * There may be a failure of individual button functions. Reconfigure the button functions, if configurable. * There may be a radio link failure/fault. Establish a cable connection. * The 14-function foot control panel's position sensor may always detect the rest position. Establish a cable connection. * There may be a weak radio signal. Establish a cable connection. * There may be no pairing with the stand. Perform pairing.
T
Timothy ElliottAug 30, 2025
How to improve red reflex in Zeiss Microscope?
- E
  Eric GonzalezAug 30, 2025
  If the red reflex in your Zeiss Microscope is too dark or non-existent, consider the following: * The red reflex illumination might not be activated. Switch the red reflex illumination on. * The objective lens may be soiled. Clean the objective lens. * The light guide might not be correctly inserted. Push the light guide in as far as it will go. * The lamp reflector for the halogen lamp might not be sitting correctly in the lamp bulb. Press the lamp reflector into the lamp bulb. * The surgical microscope might not be oriented correctly. Place the device in the working position so that the main microscope axis coincides with the optical axis of the patient’s eye.
M
margaret48Sep 1, 2025
Why are functions being triggered unintentionally on my Zeiss Microscope?
- C
  Cindy WatkinsSep 1, 2025
  If functions are being triggered unintentionally on your Zeiss Microscope, consider these potential causes: * A button on the 14-function foot control panel may be mechanically stuck after being pressed. Place the 14-function foot control panel in its rest position and reconfigure the button functions if possible. * The 14-function foot control panel may be sending an erroneous activation signal. Place the 14-function foot control panel in its rest position and reconfigure the button functions if possible. * The wrong 14-function foot control panel may be in use. Check the marking to ensure it matches the stand, and perform pairing if necessary.
M
Michael WilkersonSep 3, 2025
Why is the illumination too bright in my Zeiss Microscope?
- M
  Mark OnealSep 4, 2025
  If the illumination in the surgical field of your Zeiss Microscope is too bright: * The brightness level might be set too high. Decrease the brightness on the stand or on the 14-function foot control panel. * There may be a defective light control. Activate manual mode.
D
Daniel WigginsSep 6, 2025
How to fix dark or noisy video image on Zeiss opmi lumera 700?
- C
  Crystal BrowningSep 6, 2025
  If the image on the video monitor is too dark or has a high level of noise on your Zeiss Microscope: * There may be insufficient light. Increase the brightness level of the illumination. * The incorrect light metering method may be selected for the integrated camera. Activate the "Integral" light metering method. * If using external cameras, remove the fixed stop from the external camera adapter.
Z
zhangdianaSep 8, 2025
What to do if data cannot be displayed on Zeiss opmi lumera 700?
- K
  Karen WilliamsSep 8, 2025
  If data cannot be displayed or played back on your Zeiss Microscope, consider the following: * A non-supported file format may have been imported or saved to the LAN. Use supported file formats. * Video with an incorrect video system may have been imported or saved to the LAN. Set the device to the video system for your country (PAL or NTSC) and restart the device. * The USB storage device may have been removed and reinserted. Select the desired patient file.
M
Mary KingSep 10, 2025
What to do if Zeiss Microscope shows error during system start?
- M
  Michael TaylorSep 12, 2025
  If your Zeiss Microscope shows an error during system start, it may be because a button was pressed during the system start. Restart the system, making sure not to press any buttons during the process.