Zero Zone CRYSTAL MERCHANDISER RVMC30D - Anchoring Ultra Narrow Cases

16 • Installation & Operation
INSTALLATION & OpERATION
Ultra Narrow Case Anchoring
The Crystal
™
Cooler Ultra Narrow (RVMC24UN) must be anchored to either another case or a wall to ensure the case will not tip
forward. The Back-to-Back Ultra Narrow (RVMC24BBUN) does not require anchoring. It may be used as the anchor for the Ultra Narrow case.
Two case-to-case support brackets will be provided when anchoring the Ultra Narrow to another case. The Ultra Narrow case must be set 3"
away from the other case for proper ventilation, so a provided trim piece must be eld-installed to cover the gap (See Figure 18). Two case-to-
wall support brackets will be provided when anchoring the Ultra Narrow to a wall (See Figure 19 on page 17).
FIGURE 18: Anchoring Ultra Narrow to Another Case
3"
GAP BETWEEN
CASES
1'0"
7"
9"
1'0"
4'7"
9'1 1/2"
A
LEFT SWING DOORS
RIGHT SWING DOORS
FRENCH SWING
DOORS
SCREW CASE-TO-CASE
SUPPORT BRKT (18-0066)
IN CEILING OF 2RVMC24UN
& 3RVMC24BBUN
7' 1/4"
7'1 1/4"
DETAIL A
CASE-TO-CASE TRIM (37-0528-XP1)
SCREW CASE-TO-CASE TRIM
TO END TRIM ON VMC24BBUN
DOUBLE STICK TAPE THE
CASE-TO-CASE TRIM TO
THE 2RVMC24UN END
PANEL
AND 3RVMC24BBUN
RELEASED
LINEUP ASSEMBLY 2RVMC24UN
66-0037
1 OF 1
B
8/15/2017
Eric Gray
(UNLESS OTHERWISE SPECIFIED)
NONE
NONE
COPYRIGHT INFORMATION
THIS DRAWING AND THE INFORMATION CONTAINED WITHIN, IS
THE SOLE PROPERTY OF ZERO ZONE, INC. ANY USE OF THIS
DOCUMENT OR DISCLOSURE OF ITS CONTENTS; BY
REPRODUCTION OR OTHER MEANS, WITHOUT THE WRITTEN
CONSENT OF ZERO ZONE, INC. IS STRICTLY PROHIBITED.
PART WEIGHT:
(IN LBS)
TOLERANCES:
(PER SP-0457)
STANDARD
FINISH:
(PER SP-0154)
MATERIAL:
(PER SP-0404)
SHEET
SIZE
B
CAD DRAWING
NO MANUAL REVISIONS
NOT TO SCALE
SCALE:
MODELED BY:
DRAWN BY:
UNLESS OTHERWISE
SPECIFIED, ALL DIMENSIONS
ARE IN DECIMAL INCH
SHEET:
DATE:
REVISION
DRAWING No:
DESCRIPTION:
110 NORTH OAKRIDGE DRIVE
NORTH PRAIRIE, WISCONSIN
USA 53153
ZERO ZONE, INC.
BY
DATE
ECN No.
REVISION DESCRIPTION No.
AR
9/29/2017
12418
CHANGED FILLER PIECES
B
REVISION INFORMATION
3"
GAP BETWEEN
CASES
1'0"
7"
9"
1'0"
4'7"
9'1 1/2"
A
LEFT SWING DOORS
RIGHT SWING DOORS
FRENCH SWING
DOORS
SCREW CASE-TO-CASE
SUPPORT BRKT (18-0066)
IN CEILING OF 2RVMC24UN
& 3RVMC24BBUN
7' 1/4"
7'1 1/4"
DETAIL A
CASE-TO-CASE TRIM (37-0528-XP1)
SCREW CASE-TO-CASE TRIM
TO END TRIM ON VMC24BBUN
DOUBLE STICK TAPE THE
CASE-TO-CASE TRIM
TO
THE 2RVMC24UN END
PANEL
AND 3RVMC24BBUN
RELEASED
LINEUP ASSEMBLY 2RVMC24UN
66-0037
1 OF 1
B
8/15/2017
Eric Gray
(UNLESS OTHERWISE SPECIFIED)
NONE
NONE
COPYRIGHT INFORMATION
THIS DRAWING AND THE INFORMATION CONTAINED WITHIN, IS
THE SOLE PROPERTY OF ZERO ZONE, INC. ANY USE OF THIS
DOCUMENT OR DISCLOSURE OF ITS CONTENTS; BY
REPRODUCTION OR OTHER MEANS, WITHOUT THE WRITTEN
CONSENT OF ZERO ZONE, INC. IS STRICTLY PROHIBITED.
PART WEIGHT:
(IN LBS)
TOLERANCES:
(PER SP-0457)
STANDARD
FINISH:
(PER SP-0154)
MATERIAL:
(PER SP-0404)
SHEET
SIZE
B
CAD DRAWING
NO MANUAL REVISIONS
NOT TO SCALE
SCALE:
MODELED BY:
DRAWN BY:
UNLESS OTHERWISE
SPECIFIED, ALL DIMENSIONS
ARE IN DECIMAL INCH
SHEET:
DATE:
REVISION
DRAWING No:
DESCRIPTION:
110 NORTH OAKRIDGE DRIVE
NORTH PRAIRIE, WISCONSIN
USA 53153
ZERO ZONE, INC.
BY
DATE
ECN No.
REVISION DESCRIPTION No.
AR
9/29/2017
12418
CHANGED FILLER PIECES
B
REVISION INFORMATION
3"
GAP BETWEEN
CASES
1'0"
7"
9"
1'0"
4'7"
9'1 1/2"
A
LEFT SWING DOORS
RIGHT SWING DOORS
FRENCH SWING
DOORS
SCREW CASE TO CASE
SUPPORT BRKT (18-0066)
IN CEILING OF 2RVMC24UN
& 3RVMC24BBUN
7' 1/4"
7'1 1/4"
DETAIL A
DOUBLE STICK TAPE
THE CASE TO CASE TRIM
TO THE 2RVMC24UN END
PANEL
CASE TO CASE TRIM (37-0528-XP1)
SCREW CASE TO CASE TRIM
TO END TRIM ON VMC24BBUN
AND 3RVMC24BBUN
RELEASED
LINEUP ASSEMBLY 2RVMC24UN
66-0037
1 OF 1
B
8/15/2017
Eric Gray
(UNLESS OTHERWISE SPECIFIED)
NONE
NONE
COPYRIGHT INFORMATION
THIS DRAWING AND THE INFORMATION CONTAINED WITHIN, IS
THE SOLE PROPERTY OF ZERO ZONE, INC. ANY USE OF THIS
DOCUMENT OR DISCLOSURE OF ITS CONTENTS; BY
REPRODUCTION OR OTHER MEANS, WITHOUT THE WRITTEN
CONSENT OF ZERO ZONE, INC. IS STRICTLY PROHIBITED.
PART WEIGHT:
(IN LBS)
TOLERANCES:
(PER SP-0457)
STANDARD
FINISH:
(PER SP-0154)
MATERIAL:
(PER SP-0404)
SHEET
SIZE
B
CAD DRAWING
NO MANUAL REVISIONS
NOT TO SCALE
SCALE:
MODELED BY:
DRAWN BY:
UNLESS OTHERWISE
SPECIFIED, ALL DIMENSIONS
ARE IN DECIMAL INCH
SHEET:
DATE:
REVISION
DRAWING No:
DESCRIPTION:
110 NORTH OAKRIDGE DRIVE
NORTH PRAIRIE, WISCONSIN
USA 53153
ZERO ZONE, INC.
BY
DATE
ECN No.
REVISION DESCRIPTION No.
AR
9/29/2017
12418
CHANGED FILLER PIECES
B
REVISION INFORMATION