Zodiac MX6 User Manual (English)

Other manuals for Zodiac MX6

Instructions For Installation And Use17 pages

Quick Start Guide2 pages

Questions and Answers:

G
Glenn EvansAug 18, 2025
How to fix a Zodiac Swimming Pool Cleaners that is immobile?
- M
  Mindy Russell MDAug 18, 2025
  If your Zodiac Swimming Pool Cleaner is immobile or moving very slowly, try the following: close the main drain line, clean and empty the skimmer and filtration pump baskets. Inspect the motor area and remove any visible debris. Remove the suction adaptor under the cleaner. Check the flow and turn on the filtration pump to verify there is no air in the system. Also, ensure the pool surface isn't covered with algae, as this can make it difficult for the cleaner to move.
C
Carl ColeAug 20, 2025
What to do if Zodiac Swimming Pool Cleaners stopped on the steps?
- J
  Jonathan KennedyAug 20, 2025
  If your Zodiac Swimming Pool Cleaner is stopped on the steps, verify that the top cover swivel turns freely. Test the flow by checking the wheel rotation speed. Also, check that the pipe is not too long.
J
Jason RamosAug 23, 2025
Why is my Zodiac MX6 cleaner immobile?
- V
  Vernon DavisAug 23, 2025
  If your Zodiac Swimming Pool Vacuum is immobile or moving very slowly, several factors could be responsible. First, ensure the main drain line is closed. Then, clean and empty the skimmer and filtration pump baskets. Inspect the motor area, removing any visible debris. Remove the suction adaptor under the cleaner and check the flow. Also, verify that there is no air in the circulation system by turning on the filtration pump. Check the cleaner's hose sections for holes or cracks, and make sure the pool surface is not covered with algae. Finally, perform shock chlorination and slightly reduce the pH.
A
Angela BrownAug 26, 2025
What to do if Zodiac Swimming Pool Vacuum cleaner is stopped on the steps?
- C
  Cindy DuranAug 26, 2025
  If your Zodiac Swimming Pool Vacuum cleaner stops on the steps, check that the top cover swivel turns freely. Test the flow by checking the wheel rotation speed. If the pipe is too long, shorten the hose length by removing sections.
P
Patrick MejiaAug 28, 2025
What to do if my Zodiac Swimming Pool Vacuum lays on its side?
- N
  Nancy RobertsAug 28, 2025
  If your Zodiac Swimming Pool Vacuum lays on its side, check that the hose float is positioned correctly on the leader hose.
M
Michelle CruzAug 30, 2025
Why is my Zodiac Swimming Pool Cleaners not covering the entire pool?
- N
  Nancy MeyersAug 30, 2025
  If your Zodiac Swimming Pool Cleaner isn't covering the entire pool, start by checking the flow. Ensure that your return line fittings are aimed downwards if they're adjustable. Inspect the hose for any coils and confirm that the hose assembly is long enough for your pool. Also, verify the position of the hose float on the leader hose section. Monitor the cleaner's movement for more than five minutes to see if each track changes direction regularly.
B
Benjamin CruzSep 2, 2025
How to make Zodiac Swimming Pool Cleaners climb the pool walls?
- K
  Kenneth MillerSep 2, 2025
  If your Zodiac Swimming Pool Cleaner is not climbing the pool walls, check the flow and increase it if necessary. Make sure the hose float is positioned correctly on the leader hose. Also, ensure that the pool walls are free of algae and not slippery.
M
Michael BanksSep 4, 2025
What to do if Zodiac Swimming Pool Cleaners climbs above the water line?
- D
  Daniel WarnerSep 4, 2025
  If your Zodiac Swimming Pool Cleaner climbs above the water line, try reducing the flow. Also, check that the hose float is positioned correctly on the leader hose.
B
Brenda DuncanSep 6, 2025
Why Zodiac Swimming Pool Cleaners lays on its side?
- S
  Savannah EllisSep 6, 2025
  If your Zodiac Swimming Pool Cleaner lays on its side, check that the hose float is positioned correctly on the leader hose.
M
Matthew BensonSep 9, 2025
What to do if my Zodiac MX6 doesn't cover the entire pool?
- S
  Scott VillegasSep 9, 2025
  If your Zodiac Swimming Pool Vacuum isn't covering the entire pool, start by checking the flow. If adjustable, aim the return line fittings in the pool downward. If a memory has formed in the hose sections, turn off the cleaner and remove the affected hose sections. Make sure the hose assembly is long enough. Check the position of the hose float on the leader hose section. Monitor the cleaner for more than five minutes, ensuring each track changes direction regularly.

Zodiac MX6 Specifications

General

Pool Type	In-ground
Cyclonic Suction	Yes
Flow Regulator Valve	Yes
Power Source	Pool's filtration system
Warranty	1 year
Cleaning Coverage	Floor and walls
Pool Surface	Concrete, tile, vinyl, and fiberglass
Type	Suction-side pool cleaner