EasyManua.ls Logo

Zoeller 1461-0006 - User Manual

Zoeller 1461-0006
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
IL1102
Your validation code for this project is
LB808344 (From old instructions)
CAST IRON
SHALLOW WELL JET PUMP
MODEL #1461-0006
Español p. 21
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-584-8089, 7:30 a.m. - 5:00 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Zoeller
®
is a registered trademark
of Zoeller Co. All Rights Reserved.
024987 D
ZoellerAtHome.com

Table of Contents

Other manuals for Zoeller 1461-0006

Preview: Instructions
Instructions11 pages

Questions and Answers

  • K
    Kathleen ClarkAug 4, 2025
    How to fix little or no discharge from Zoeller Water Pump?
    • M
      Michael SaundersAug 5, 2025
      If your Zoeller Water Pump has little to no discharge, the following could be the cause. Ensure the pump casing is initially filled with water. If the suction lift is too high or long, move the pump closer to the water source. Repair or replace any holes or air leaks in the suction line, using pipe tape and sealing compound. Make sure the foot valve is appropriately sized to the piping, or install one size larger. Submerge the foot valve or suction line deeper in the water. Check the motor wiring against the wiring diagram. Replace a leaking casing gasket. Finally, ensure that suction or discharge line valves are open.
  • M
    Michele TrevinoAug 10, 2025
    Why Zoeller 1461-0006 will not deliver water or develop pressure?
    • R
      Rebecca McknightAug 10, 2025
      If your Zoeller Water Pump isn't delivering water or developing pressure, start by ensuring the pump casing is filled with priming water. Next, check for any leaks in the suction line and repair or replace as necessary. Make sure the discharge line is open, allowing priming air to escape. Also, verify that the suction line (or valve) is open. If the foot valve is leaking, replace it. Lastly, inspect the suction screen for clogs and clean or replace it if needed.
  • T
    troytaylorAug 16, 2025
    Why does my Zoeller 1461-0006 keep losing suction?
    • R
      ryan50Aug 16, 2025
      If your Zoeller Water Pump is experiencing a loss of suction, there are several potential causes. First, check for air leaks in the suction line and repair or replace as needed. If the suction lift is too high, lower it, install a foot valve, and prime the pump. Ensure sufficient inlet pressure or suction head by adding more water to the tank or increasing back pressure. Lastly, inspect the foot valve or strainer for clogs and unclog if necessary.
  • R
    richmondthomasAug 22, 2025
    What to do if my Zoeller Water Pump will not start or run?
    • K
      Kayla WelchAug 22, 2025
      If your Zoeller Water Pump isn't starting or running, several factors could be at play. First, verify the wiring is correct by checking the wiring diagram on the motor. A blown fuse or open circuit breaker can also prevent the pump from starting, so replace the fuse or close the circuit breaker. Additionally, inspect for loose or broken wiring, tightening connections or replacing any damaged wires. In some cases, a stone or foreign object might be lodged in the impeller, requiring you to disassemble the pump to remove it. If the motor is shorted out, it will need to be replaced. Finally, if the thermal overload has opened the circuit, allow the unit to cool down before restarting, after identifying the cause of the overload.
  • P
    Pamela MillerAug 28, 2025
    How to reduce vibration and noise in Zoeller Water Pump?
    • J
      joshuarogersAug 28, 2025
      If your Zoeller Water Pump vibrates or makes excessive noise, it could be due to several reasons. Check if the mounting plate or foundation is not rigid enough, and reinforce it if needed. Disassemble the pump and clean any foreign material that may be inside. If the impeller is damaged, replace it. Lastly, worn motor bearings can also cause these issues, so replace them if necessary.

Summary

Safety Information

DANGER

Critical warnings about electrical shock hazards.

WARNING

Alerts and precautions for electrical shock.

Well to Pump Connection (Suction Pipe)

Pump to Pressure Tank Connection (Discharge Pipe)

Tank to House Connection

Pump Electrical Connections

Wiring the Pressure Switch

Step-by-step guide for connecting motor and power supply to the switch.

Changing Voltage (115 V to 230 V)

Voltage Conversion Procedure

Details how to change wiring on the terminal board for 230V service.

Pump Priming & Startup

Priming Procedure

Step-by-step instructions for filling the pump cavity with water.

Startup and Troubleshooting

Turning on the breaker and initial checks for pump operation.

Care and Maintenance

Winterizing

Quick Trouble-Shooting Checklist

Pump Not Running

Pump Runs Continuously

Pump Wont Shut Off

Troubleshooting

Little or No Discharge

Addresses causes like improper filling or air leaks in suction line.

Pump Will Not Deliver Water

Covers issues from no priming water to clogged suction screens.

Loss of Suction

Troubleshoots air leaks, high suction lift, and insufficient inlet pressure.

Pump Vibrates or Makes Noise

Pump Will Not Start or Run

Addresses wiring, blown fuses, broken wiring, or motor issues.

Zoeller 1461-0006 Specifications

General IconGeneral
Model1461-0006
TypeSubmersible Sump Pump
Horsepower1/2 HP
Voltage115V
Maximum Head25 ft
Motor Housing MaterialCast Iron
Impeller MaterialThermoplastic
Switch TypeVertical Float Switch
Thermal ProtectionYes
PhaseSingle Phase
Discharge Size1-1/2 inches NPT
Cord Length10 feet
Power Cord Length10 feet
Warranty3 years

Related product manuals