2
© Copyright 2017 Zoeller
®
Co. All rights reserved.
Limited Warranty
Preinstallation Checklist
any other abusive entity, etc. in all pumping applications. The warranty set out in
the paragraph above is in lieu of all other warranties expressed or implied; and we
do not authorize any representative or other person to assume for us any other
liability in connection with our products.
Contact Manufacturer at 3649 Cane Run Road, Louisville, Kentucky 40211 USA,
Attention: Customer Support Department to obtain any needed repair or replacement
of part(s) or additional information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED
OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE
LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY.
Some jurisdictions do not allow limitations on the duration of an implied warranty,
so the above limitation may not apply to you. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
This warranty gives you specic legal rights and you may also have other rights
which vary from jurisdiction to jurisdiction.
Manufacturer warrants, to the purchaser and subsequent owner during the warranty
period, every new product to be free from defects in material and workmanship
under normal use and service, when properly used and maintained, for a period
of one year from date of purchase by the end user, or 18 months from date of
original manufacture of the product, whichever comes rst. Parts that fail within
the warranty period, one year from date of purchase by the end user, or 18 months
from the date of original manufacture of the product, whichever comes rst, that
inspections determine to be defective in material or workmanship, will be repaired,
replaced or remanufactured at Manufacturer's option, provided however, that by so
doing we will not be obligated to replace an entire assembly, the entire mechanism
or the complete unit. No allowance will be made for shipping charges, damages,
labor or other charges that may occur due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any material
or product that has been disassembled without prior approval of Manufacturer,
subjected to misuse, misapplication, neglect, alteration, accident or uncontrollable
act of nature; that has not been installed, operated or maintained in accordance
with Manufacturer's installation instructions; that has been exposed to outside
substances including but not limited to the following: sand, gravel, cement, mud,
tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other
abrasive or corrosive substances, wash towels, feminine sanitary products, or
1. Inspect your pump. Occasionally, products are damaged during shipment. If the
unit is damaged, contact your dealer before using. DO NOT remove the test plugs
in the cover nor the motor housing.
2. Carefully read the literature provided to familiarize yourself with specic details
regarding installation and use. These materials should be retained for future reference.
SEE BELOW FOR
LIST OF WARNINGS
1. Make sure the power source is capable of handling the electrical
requirements of the grinder pump, as indicated on the nameplate.
2. A disconnect switch should be installed in the circuit bringing electrical
power to the pump.
3. The progressing cavity grinder pumps are operated by variable level oat
control switches. It is the responsibility of the installing party to see that oat
control switches will not hang up on the grinder pump or other pit peculiarities
and are secured so that the grinder pump will shut off. It is recommended to
use rigid pipe and ttings and the pit be at least 61 cm (24") in diameter for
simplex systems and 91.4 cm (36") or larger in diameter for duplex systems.
4. Grinder installations should be checked yearly for debris and/or build up
which may interfere with the “ON” or “OFF” positions of variable level oat
control switches. Repair and service, other than cutter assembly maintenance,
should be performed by a Zoeller Authorized Service & Warranty Center or
Customer Care Center.
5. Maximum operating temperature must not exceed 54 °C (130 °F).
6. Do not operate an unsubmerged progressing cavity pump. Dry pump
operation may damage the hydraulic stator due to lack of lubrication. Do
not run dry.
7. To ensure proper pump operation, a swing or apper style check valve
must be installed in the pump discharge line. A faulty or non-functional
check valve when combined with a pressure sewer may prevent the
pump from starting.
1. Make sure pump connection contains a ground terminal. The power cord
on all Zoeller Progressing Cavity Grinder Pumps contains a green conductor
for grounding to help protect you against the possibility of electric shock.
2. Make certain the electrical service is within reach of the power supply
cord.
3. Make sure any panels and branch circuits are equipped with proper size
fuses and circuit breakers. An independent power circuit is recommended,
sized according to the National Electrical Code, for the current shown on
the grinder pump nameplate.
4. For your protection, always disconnect the power source to the grinder
pump before handling. All grinder pumps must be properly grounded and
wired in accordance with the “National Electrical Codes” and all local codes
and ordinances.
5. Installation of electrical hardware and checking of control panels
and circuits should be performed by a qualied licensed electrician.
6. Risk of electrical shock - These pumps have not been investigated for use
in swimming pool areas.
7. According to the state of California (Prop 65), this product contains chemicals
known to the state of California to cause cancer and birth defects or other
reproductive harm.
NOTE: Pumps with the UL mark and the US mark are tested to UL standard UL778.
CSA-certied pumps are certied to CSA standard C22.2 No. 108.
SEE BELOW FOR
LIST OF CAUTIONS
Do not attempt to turn the cutter blades
located on bottom of the unit with ngers. Use a wrench
when checking or removing the cutter.
Progressing cavity grinder pumps are designed for
pressure sewer applications. A UL listed and CSA certified pressure relief
valve must be installed in the system to prevent excessive pressure buildup.
To Next Page
Loading...
