Zoom 2100 - Managing Effect Modules and Patches; Turning Effect Modules On;Off; Storing and Copying Patches

11
In Edit mode, use the parameter select key
to select the module to turn on and off.
Press the [ON/OFF] key.
The corresponding module is turned on or off.
• Instead of the parameter select keys, you can use foot
switches 1–3 or the [BANK▲] switch to turn the effect
module on and off.
• In step you can also press and hold the parameter
select key for more than one second to turn the selected
module on and off. The parameter select key of the
SAMPLER module, however, is a special key used to
enter Sampler mode, and cannot be used to turn other
modules on and off.
The module on/off setting is stored as part of the
corresponding patch.
HINTHINT
Type(RTM)
Sens
/
Rate
POSITION
POSITION 1.COMP/WAH•DIST
2.DIST•COMP/WAH
COMP
/
WAH
Type
Gain
/
Top
Tone
/
Body
LevelPatch Level
DIST
Treble
Middle
Bass
ZNR
EQ
Type
Depth
/Time
Rate
/Pit/FB
Mix
/Mode
MOD
Type
Time
Tone
/FB
Mix
REV
/
DLY
1.AUX Mix
3.AUX Rch
2.AUX Lch
1.COMP
2.PEDAL-WAH
3.AUTO-WAH
4.TREMOLO
5.RING MOD
6.SLOW ATTACK
4.PLAYNOTE
Max Rec Time
Constant Pitch
Tone
Gain TrimMaster Level
JAM 1 JAM 2 JAM 3 JAM REC
Presence Amp Sim Rev Trim FUNCTION
SAMPLER COMP
/
WAH
UTILITY
PARM
1.CLEAN
2.OVER DRIVE
3. DISTORTION
4.FUZZ
/
GRUNGE
5.LEAD
6.METAL
7.ACOUSTIC
DIST
1.CHORUS
2.STEREO CHO
3. FLANGER
4.PHASE
5.PITCH
6.PEDAL-PITCH
7.DELAY
MOD
1.HALL
2.ROOM
3.PP-DELAY 1
4.PP-DELAY 2
REV/
DLY
JAM PLAY
MONITOR
ON
/
OFF
VALUE
+
–
B
321
GROUP(EXIT)
PATCHBANK
STORE
PRESETBOTH
BANK
SAMPLER
FUNCTION
SPEED
REC
Turning an effect module on and off
Press the [STORE] key in Play mode or Edit
mode.
The 2100 enters store standby mode.
Use the [BANK▲] switch and foot switches
1–3 to select a copy destination patch.
If you do not specify the destination, the original
bank number and the patch number will be
automatically selected.
You cannot store the patch in the PRESET group. If a
patch from the PRESET group is selected before you
perform step , pressing the [STORE] key will
automatically select patch “01” of the USER group. Select
the desired bank number and patch number.
Press the [STORE] key again to store (copy)
the patch. If you wish to cancel the store
operation, press the [GROUP/EXIT] key
instead.
The patch is stored and the 2100 returns to Play
mode.
• When you execute the store (copy) operation, the patch
in the destination will be erased and cannot be
recovered. You can, however, revert any patch or all
patches in the USER group to their factory default
settings. (See page 20.)
• You can also use the [VALUE+/–] keys to select the
copy (store) destination.
NOTE
NOTE
Type(RTM)
Sens
/
Rate
POSITION
POSITION 1.COMP/WAH•DIST
2.DIST•COMP/WAH
COMP
/
WAH
Type
Gain
/
Top
Tone
/
Body
LevelPatch Level
DIST
Treble
Middle
Bass
ZNR
EQ
Type
Depth
/Time
Rate
/Pit/FB
Mix
/Mode
MOD
Type
Time
Tone
/FB
Mix
REV
/
DLY
1.AUX Mix
3.AUX Rch
2.AUX Lch
1.COMP
2.PEDAL-WAH
3.AUTO-WAH
4.TREMOLO
5.RING MOD
6.SLOW ATTACK
4.PLAYNOTE
Max Rec Time
Constant Pitch
Tone
Gain TrimMaster Level
JAM 1 JAM 2 JAM 3 JAM REC
Presence Amp Sim Rev Trim FUNCTION
SAMPLER COMP
/
WAH
UTILITY
PARM
1.CLEAN
2.OVER DRIVE
3. DISTORTION
4.FUZZ
/
GRUNGE
5.LEAD
6.METAL
7.ACOUSTIC
DIST
1.CHORUS
2.STEREO CHO
3. FLANGER
4.PHASE
5.PITCH
6.PEDAL-PITCH
7.DELAY
MOD
1.HALL
2.ROOM
3.PP-DELAY 1
4.PP-DELAY 2
REV/
DLY
JAM PLAY
MONITOR
ON
/
OFF
VALUE
+
–
B
321
GROUP(EXIT)
PATCHBANK
STORE
PRESETBOTH
BANK
SAMPLER
FUNCTION
SPEED
REC
Storing and copying a patch
When you select another patch, the edited patch is reset to its pre-edited status, unless you store
the patch into memory. If you have created a favorite patch, be sure to store it. You can also make
a copy of an existing patch by storing it in a different location. If you copy the patches for the same
song into the same bank, it is much easier and quicker to switch between the patches during
performance.
NOTE
NOTE