Zoom 2100 - Adjusting Tone and Volume for Environment; Global Parameter Adjustments; FUNCTION Switch Assignment

5
Press the [UTILITY] key in Play mode.
The [UTlLITY] key is used to access the global
parameters that are shared by all patches.
Use the parameter select keys to choose
the desired global parameter.
The LED of the currently-selected global
parameter flashes.
Use the [VALUE +/–] key to edit the value.
The following parameters are adjustable in the
specific range:
■ Master Level
Enables you to set the final volume level of the
2100 in the range of 1 through 30.
■ Gain Trim
Enables you to set the intensity of distortion (the
input gain of the gain parameter) when you use a
distortion effect (type 2–6) for the DIST module.
This parameter is set to “7” when you turn on the
power to the unit.
Make fine adjustments according to the acoustic
environment and the guitar being used.
■ Presence
Enables you to adjust the tonal quality of the
presence in the range of –12 to +12.
■ Amp Sim (Amp Simulator)
You can apply the amp simulator effect (to
simulate the unique characteristics of a guitar
amplifier). Select from the following:
• oF (off): The amp simulator effect is turned off.
•Co (combo): This effect simulates the sound
produced by a 100W combo amplifier.
•bC (bright combo): This effect simulates the
bright sound produced by a 120W amplifier that
emphasizes the high range.
•St (stack): This effect simulates the sound
produced by a stack amplifier with four speakers
stacked up.
■ Rev Trim (Reverb Trim)
Enables you to set the input gain of the
reverberation (mix) of the effects used for the
REV/DLY module in the range of 1 through 10.
This parameter is set to “7” when you turn on the
power to the unit.
Adjust this parameter according to the acoustic
environment of the performance.
■ FUNCTION
(The function of the [FUNCTION] switch)
Enables you to assign a function to the
[FUNCTION] switch. Refer to page 8 for more
information on the assignable functions and the
operation of the [FUNCTION] switch.
When you finish setting the global
parameters, press the [GROUP/EXIT] key.
The 2100 enters Play mode.
The global parameter settings are not affected even if you
switch the patches. These parameters are reset when you
turn off the power to the 2100.
As an exception, however, you can store the “AmpSim”
and “FUNCTION” settings. To store these settings, select
the desired patch and follow the steps for the store
operation (see page 11).
NOTE
HINTHINT
REV Trim Mix
HINTHINT
Gain Trim GAIN
Type(RTM)
Sens
/
Rate
POSITION
POSITION 1.COMP/WAH•DIST
2.DIST•COMP/WAH
COMP
/
WAH
Type
Gain
/
Top
Tone
/
Body
LevelPatch Level
DIST
Treble
Middle
Bass
ZNR
EQ
Type
Depth
/Time
Rate
/Pit/FB
Mix
/Mode
MOD
Type
Time
Tone
/FB
Mix
REV
/
DLY
1.AUX Mix
3.AUX Rch
2.AUX Lch
1.COMP
2.PEDAL-WAH
3.AUTO-WAH
4.TREMOLO
5.RING MOD
6.SLOW ATTACK
4.PLAYNOTE
Max Rec Time
Constant Pitch
Tone
Gain TrimMaster Level
JAM 1 JAM 2 JAM 3 JAM REC
Presence Amp Sim Rev Trim FUNCTION
SAMPLER COMP
/
WAH
UTILITY
PARM
1.CLEAN
2.OVER DRIVE
3. DISTORTION
4.FUZZ
/
GRUNGE
5.LEAD
6.METAL
7.ACOUSTIC
DIST
1.CHORUS
2.STEREO CHO
3. FLANGER
4.PHASE
5.PITCH
6.PEDAL-PITCH
7.DELAY
MOD
1.HALL
2.ROOM
3.PP-DELAY 1
4.PP-DELAY 2
REV/
DLY
JAM PLAY
MONITOR
ON
/
OFF
VALUE
+
–
B
321
GROUP(EXIT)
PATCHBANK
STORE
PRESETBOTH
BANK
SAMPLER
FUNCTION
SPEED
REC
Adjusting the volume level and tonal quality according to the acoustic environment
The 2100 features global parameters that enable you to adjust the master level and the degree of
distortion applied to all patches on a global scale. Use these parameters to adjust the volume level
and tonal quality to suit the characteristics of the instruments, amplifiers, and the acoustic
environment.