To Next PageTo Next Page
Need help?Do you have a question about the Zoom G3 and is the answer not in the manual?
General| Looper | 40 seconds |
|---|---|
| Sampling Frequency | 44.1 kHz |
| A/D Conversion | 24-bit |
| D/A Conversion | 24-bit |
| Display | LCD |
| Type | Multi-effects processor |
| Simultaneous Effects | 6 |
| Frequency Response | 20Hz - 20kHz |
| Inputs | 1 x 1/4" instrument |
| Outputs | 2 x 1/4" (L/mono, R) |
| USB | Yes |
| Power Source | AC adapter (included) |
| Effects | Delay, Reverb |
| Dimensions | 181 mm (D) x 234 mm (W) x 58 mm (H) |
Explains Warning/Caution symbols for accident prevention.
Covers AC adapter and battery operation guidelines.
Covers product handling, environment, AC adapter safety.
Covers interference, cleaning, malfunction, copyrights.
Highlights key features like effects, modeling, and looper.
Defines essential terms like 'Patch' and 'Bank' for manual clarity.
Describes buttons and displays on the top surface of the unit.
Details input/output jacks and connectors on the back.
Identifies expression pedal, knobs, switches, and foot switches.
Details AC adapter, USB, control inputs, and specific switches.
Steps to turn the unit on using batteries or adapter.
Explains the automatic standby feature for power saving.
Shows current patch information and effect graphics.
Illustrates parameter editing with names, tabs, and values.
How to toggle individual effects using footswitches.
How to change the type of effect displayed.
How to adjust parameter values using knobs.
How to switch between different parameter pages.
Explains processing limits and "DSP Full!" message.
How to view more than three effects in the chain.
How to enter the mode for selecting patches.
Methods to navigate between different patches.
How to move between groups of 10 patches.
How to exit patch selection and return to the main display.
Steps to begin saving or swapping a patch.
Selecting the desired action (store/swap).
Specifying the location to save or swap.
Finalizing the patch saving or swapping process.
How to enter the menu for patch-specific settings.
Steps to rename a patch and adjust its volume.
Changing effect sequence and customizing footswitch actions.
Linking pedal movement to effect parameters.
Setting pedal min/max values and leaving the TOTAL menu.
How to enter system settings and adjust master volume.
Adjusting global tempo and using tap tempo input.
Optimizing output for different gear connections.
Modifying signal path and configuring display backlight timeout.
Setting battery type, checking eco mode, and adjusting display contrast.
Configuring auto save and adjusting USB audio monitoring balance.
Setting record level, viewing firmware, and exiting GLOBAL menu.
How to start the tuner, set pitch, and select tuner type.
Using alternate tunings and the guitar tuning procedure.
Activating, choosing, and setting tempo for rhythm patterns.
Adjusting rhythm level and stopping/managing patterns.
Starting looper, setting duration, and adjusting tempo.
Steps for capturing, replaying, and halting audio loops.
Adding layers to loops and clearing loop data.
Setting loop levels and exiting the looper function.
Enabling undo and configuring loop stop behavior.
Setting immediate stop, fade out, or end of loop playback.
Lists supported OS and details quantization/sampling rate.
Calibrating sensitivity and adjusting physical pedal resistance.
Covers downloading, preparing, and executing firmware updates.
Finishing updates and restoring default settings.
Explains effects like Comp, GraphicEQ, ZNR.
Covers OverDrive, amp models, filters.
Details Chorus, Flanger, Pitch Shifters, Delays.
Covers reverbs, looper, wah, synths.
Solutions for power, no sound, or low volume problems.
Troubleshooting noise, sound quality, and pedal issues.
Fixing low DAW recording levels and rapid battery drain.
Details on effects, patches, I/O, dimensions, and power.
An enumeration of available rhythm patterns and their time signatures.
