Zte MF25A User Guide

MF25A
Let’s go
Getting started with your device.
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Connecting Your Device
Follow the number to connect your device.
NOTE:
• If you want to use the mobil e n etwork to connec t t o I nternet, you
need to insert your (U)SIM card rst.
• Your device does not support Micro/Nano or any other nonstandard
SIM cards. To avoid device damage, please do not use them.
Normal states of the indicators are shown below:
Indicator State Description
POWER
ON External power supply is connected normally.
OFF
External power supply is disconnected or
power off.
WIFI
ON
WLAN works normally with no data
transmission..
Blinking WLAN works normally with data transmission.
OFF
WLAN works abnormally, or this WLAN
function is disabled.
PHONE
Off Not in use.
Blinking
On Dialing, or there is an incoming call, the
phone is ringing.
On In calling.
PPP
ON WAN connection established (PDP activated)
Blinking WAN connection establishing (PDP activating)
OFF
WAN connection not established (PDP not
activated).
2G/3G
ON
RF signal is normal (RSSI >= -90dBm).
Different color indicates different network.
Red: GSM/GPRS/EDGE.
Green: HSDPA/HSUPA/UMTS.
Blinking
RF signal is poor (-100dBm <= RSSI <
-90dBm).
OFF RF signal is not available (RSSI < -100dBm).
LAN
ON The corresponding LAN port is connected
Blinking
The corresponding LAN port is connected
with data transmission.
Off No network cable connected.
Conguring Your PC
Follow the following steps and gures for Windows XP to con gure the
Internet Protocol for your connection.
NOTE:
• Wireless Network Connection is used for Wi-Fi connection.
• Local Area Connection is used for Network Cable connection.
1. Right-click My Network Places, and then select Properties.
2. Right-click the icon for Connection, and then select Properties.
3. Select Internet Protocol (TCP/IP), and then click Properties.
4. Select these two items, and then click OK to nish the conguration.
Accessing the Internet
Before accessing the Internet, please make sure:
• Your device is connected via network cable or Wi-Fi.
• Your PC is congured.
To access the Internet:
1. Log in the WebGUI Conguration Page.
1) Launch the Internet browser and enter http://192.168.0.1 in the
address bar. The login page appears.
2) Input the password (the default p assword is admin), and then
click Login.
2. Select current mode Change.
NOTE:
If you select Bridge mode, you need to connect your clients to the LAN
ports via Ethernet cable, and use normal methods to surf directly on your
clients. If you want to use other operation mode after Bridge, you need to
restore your device.
3. Congure Settings.
NOTE : This step is u sed for Cabl e Bro adb and mode and Wirel ess
Broadband mode.
• For Cable Broadband mode
NOTE: In this mode, you can only use Wi-Fi to connect to your device.
u
Please select PPPoE, set the PPPoE par ameters, an d then click
Apply.
NOTE: Your service provider gives you the User Name and Password.
LEGAL INFORMATION
Copyright © 2013 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
photocopying an d microlm, without the pr ior written permission of ZTE
Corporation.
The manual is publi shed by ZTE Corpora tion. We reserve the right to
make modications on print errors or update specications without prior
notice.
Version No. : R1.0

Zte MF25A Specifications

General

Brand	Zte
Model	MF25A
Category	Wireless Router
Language	English