How to improve poor Wi-Fi signal on Zte Spro 2?
If you're experiencing a poor Wi-Fi signal on your Zte Projector, it could be due to a weak Wi-Fi network signal at your current location. Try moving closer to the Wi-Fi hotspot or to a location where there are no obstacles between your device and the hotspot. Also, try uninstalling recently installed software that may be causing the problem.
Why is my Zte Spro 2 Projector unable to connect to the network?
There are several reasons why your Zte Projector may be unable to connect to the network. It could be due to an invalid micro-SIM card (in this case, you should contact your service provider), being outside of the network's service area (check with your service provider), or a poor signal. If the signal is poor, try moving to an open space or closer to a window if you're inside.
Why does my Zte Spro 2 Projector have poor reception?
Poor reception on your Zte Projector can occur if the network signal is weak, such as in a basement or near a tall building, because wireless transmissions cannot effectively reach it. In this case, move to a location where the network signal can be properly received. Also, the network might be busy, especially during peak times, so avoid using your device then or try again later. Another reason may be that you are too far away from a base station. You can request a service area map from your service provider.
Why does my Zte Spro 2 Projector have a shortened standby time?
Shortened standby time on your Zte Projector can be due to several factors. If you are in an area with a weak signal, temporarily power off your device. High temperatures can also shorten battery life, in that case, contact the dealer to replace the battery. Additionally, if your device can't connect to the network, it will continuously search for a base station, consuming battery power. Try moving to an area with network access or temporarily turn off your device.
What to do if the battery of Zte Spro 2 cannot be charged or the charging is slow?
If your Zte Projector battery isn't charging or is charging slowly, the battery or charger might be damaged, in that case, contact the dealer. Another possibility is that the device's temperature is too low (below 0 °C) or too high (above 45 °C); adjust the charging environment to avoid temperature extremes. Also, check all connectors to ensure they are properly connected, as poor contact between the device and charger can cause this issue.
What to do if I get a micro-SIM card error on my Zte Spro 2?
If your Zte Projector displays a micro-SIM card error, the card itself may be malfunctioning or damaged; take it to your service provider for testing. Ensure the micro-SIM card is inserted properly. Also, check for debris on the micro-SIM card contacts and clean them with a soft, dry cloth if necessary.
Why I am unable to select certain features on Zte Spro 2?
Your service provider may not support these features, or you have not applied for services that provide these features. Contact your service provider.
What to do if the PIN code is blocked on Zte Projector?
If the PIN code on your Zte Projector is blocked, it is because you have entered an incorrect PIN code three consecutive times. Contact your service provider. If they provide the micro-SIM card’s PUK code, use the PUK code to unlock the micro-SIM card.
Guide to inserting the micro-SIM card into the device.
Instructions for fully charging the device's battery before first use.
How to connect the device to a computer using a USB cable for data transfer.
Procedures for backing up data and restoring the device to factory settings.
Important safety precautions for using the device in various environments.
Information regarding the device's compliance with RF exposure limits.
General| Display Technology | DLP |
|---|---|
| Resolution | 1280 x 720 |
| Brightness | 200 lumens |
| Contrast Ratio | 1000:1 |
| Processor | Qualcomm Snapdragon 800 |
| RAM | 2 GB |
| Internal Storage | 16 GB |
| Battery Capacity | 6300 mAh |
| HDMI | 1 x HDMI |
| Aspect Ratio | 16:9 |
| Lamp Life | 20, 000 hours |
| SD Card Slot | MicroSD |
| Operating System | Android 4.4 |
| Wi-Fi | 802.11 a/b/g/n |
| Bluetooth | 4.0 |
| USB Ports | 1 x microUSB |
| Weight | 550 g |
To Next Page
