What to do if I cannot access the Internet with my ZyXEL Communications Wireless Router?
First, check the ZyXEL Communications Wireless Router's connection to the cable or DSL device. If that doesn't work, unplug the power of both the Cable/DSL modem and the ZyXEL Communications Wireless Router, then plug them back in to reboot them. Also, verify your settings by clicking on WAN Port.
Why can't my ZyXEL Communications P-330W get a WAN IP address from the ISP?
If you're using a cable modem with your ZyXEL Communications Wireless Router, power off the cable modem for 2-3 minutes after connecting it to the router. The WAN IP address is provided after the ISP verifies the MAC address, host name, or user ID. Determine the verification method used by your ISP and configure the corresponding settings. If your ISP checks the WAN MAC address, clone the MAC address from a LAN computer by going to WAN Port and entering the MAC address in the Clone MAC Address field. If the ISP checks the user ID, navigate to WAN Port and verify your service type, user name, and password.
What to do if I cannot ping any computer on the LAN using my ZyXEL Communications P-330W?
If the 10/100M LAN LEDs are off, check the cable connections between the ZyXEL Communications Wireless Router and your LAN computers. Ensure that the IP address and subnet mask of both the router and the LAN computers are within the same IP address range.
How to fix the issue when I cannot access the P-330W ZyXEL Communications Wireless Router from the LAN?
Check the cable connection between the ZyXEL Communications Wireless Router and your computer or hub. Ping the router from a LAN computer. Ensure your computer's Ethernet card is properly installed and functioning.
What to do if none of the LEDs turn on when I turn on my ZyXEL Communications Wireless Router P-330W?
Make sure the correct power adapter is connected to the ZyXEL Communications Wireless Router and plugged into a working power source. Check all cable connections. If the LEDs still don't turn on, it might be a hardware problem, and you should contact ZyXEL.
Wireless Specifications| power output at 54Mbps | 14.2 dBm |
|---|---|
| power output at 11Mbps | 18.4 dBm |
| receive sensitivity at 54Mbps | -70 dBm |
| receive sensitivity at 11Mbps | -86 dBm |
| antenna gain | 2 dBi |
Hardware Specifications| LAN ports | Four 10/100Base-T Ethernet, full duplex RJ-45 connector with auto MDI/MDIX support |
|---|---|
| WAN port | One 10/100Base-T Ethernet, full duplex RJ-45 connector with auto MDI/MDIX support |
| power supply | 12V AC, 800 mA |
Operating Environment| temperature range | -10℃ to 55℃ |
|---|---|
| humidity range | 10% to 90% non-condensing |
Details the advanced features and capabilities of the wireless router.
Lists and describes various methods for connecting to the internet.
Explains features like Firewall, DDNS, DMZ, URL filtering, and access control.
Covers standards compliance, speed, WEP support, and MAC access control for wireless.
Describes the 4-port switching hub and DHCP server capabilities.
Details easy setup, file management, remote access, diagnostics, and UPnP.
Covers password protection, WEP, NAT protection, and DoS attack prevention.
Describes the status indicators on the front panel of the router.
Details physical connections and the function of the reset button.
Lists necessary hardware, software, and connections for setup.
Provides a step-by-step guide for physical router installation.
Introduces the guided setup process for initial configuration.
Explains how to access and use the web-based configuration interface.
Details the steps to connect to the router via a web browser.
Provides solutions for common problems when connecting for setup.
Sets the router's time zone and enables NTP client updates.
Configures the local area network IP address and subnet mask.
Configures the internet connection type and parameters.
Sets up basic wireless network parameters like SSID and channel.
Describes connection methods for cable modems.
Describes connection methods for DSL modems.
Details IP address, subnet mask, and DHCP server settings.
Explains how to set a password for router access.
Describes how to view internet, LAN, and system status information.
Configures band, SSID, channel, and other basic wireless settings.
Covers authentication type, preamble, and SSID broadcasting.
Scans for active wireless access points in the vicinity.
Introduces different wireless security methods and their impact.
Details setup for WEP encryption and WPA/TKIP security.
Allows control over which wireless devices can connect based on MAC address.
Sets up rules to restrict network access based on ports or services.
Configures DDNS for remote access using a domain name.
Sets up a DMZ host for exposing specific computers to the internet.
Configures port forwarding to allow external access to internal servers.
Defines rules for non-standard internet applications blocked by firewall.
Configures internet connection type, DNS, and MAC address cloning.
Allows testing network connectivity to IP addresses or hostnames.
Enables protection against Denial of Service attacks.
Performs DNS lookups to diagnose name resolution issues.
Configures access to the router via the internet.
Manages router settings by backing up or restoring configuration files.
Configures logging of router activities and remote log server.
Sets up rules to filter network traffic based on IP addresses.
Sets up rules to filter network access based on MAC addresses.
Displays packet counters for wireless and Ethernet network activity.
Explains necessary network settings for client PCs.
Details how to configure Windows PCs for internet access.
Configures Windows 98/ME to obtain IP address automatically via DHCP.
Configures Windows 98/ME with a static IP address.
Sets the default gateway and DNS server addresses in Windows 98/ME.
Details how to access TCP/IP properties in Windows NT 4.0.
Explains DHCP and manual IP configurations for Windows NT 4.0.
Covers advanced gateway and DNS settings in Windows NT 4.0.
Details IP address and DNS server settings for Windows NT 4.0.
Details how to access TCP/IP properties in Windows 2000.
Explains DHCP and manual IP configurations for Windows 2000.
Details how to access TCP/IP properties in Windows XP.
Explains DHCP and manual IP configurations for Windows XP.
Guides through setting up internet access for older Windows versions.
Guides through setting up internet access for Windows XP.
Configures AOL software to use the wireless router.
Details network configuration for Macintosh computers.
Explains network settings for Linux and other Unix systems.
Configures client wireless devices to connect to the access point.
Introduces common problems and solutions for the wireless router.
Addresses issues with connecting to the router and the internet.
Troubleshoots issues related to internet connectivity and timeouts.
Resolves issues with locating the access point and slow wireless speeds.
Provides in-depth solutions for general connection issues.
Diagnoses and resolves 'time out' errors during internet access.
Solves problems with specific internet applications not functioning correctly.
Addresses slow wireless speeds and environmental interference.
Explains Ad-hoc and Infrastructure modes for wireless networks.
Defines a Basic Service Set formed by stations and an access point.
Describes channel selection for optimal wireless performance.
Details the Wired Equivalent Privacy encryption standard.
Guides on configuring client wireless stations for network access.
Lists the physical and technical specifications of the router.
Details the standards, frequency, and data rates of the wireless interface.
Lists compliance with European safety and EMC directives.
Provides a warning about potential radio interference in domestic environments.
Outlines FCC limits for radiation exposure and installation guidelines.
Declares compliance with relevant European and Canadian regulations.
To Next Page
