5
Table 1 – Specifi cations
INTERMEDIATE BRACKET SPECIFICATIONS:
Figure 1 Part Number Description Material
Minimum
Breaking
Strength
kN (lb)
Lifeline Tensioning
kN (lb)
E
7241412 Intermediate Bracket 316 Stainless Steel 38 (8,543) 0.8 (180) or 5 (1,125)
7241413 Variable Intermediate Bracket 316 Stainless Steel 30 (6,744) 0.8 (180) or 5 (1,125)
7241414 Variable Mount Angle Intermediate Bracket 316 Stainless Steel 24 (5,400) 0.8 (180) or 5 (1,125)
7241415 45 Degree Intermediate Bracket 316 Stainless Steel 24 (5,400) 0.8 (180) or 5 (1,125)
Maximum Entry/Exit Angle: The maximum angle at which the HLL cable can enter or exit each Intermediate Bracket is 15°.
CORNER BRACKET SPECIFICATIONS:
Figure 1 Part Number Description Material
Minimum
Breaking
Strength
kN (lb)
Lifeline Tensioning
kN (lb)
F
7241406 90 Wall & OH Internal Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
7241407 90 Wall & OH External Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
7241408 90 Post internal Mount 316 Stainless Steel 22.2 (5,000) 0.8 (180)
7241409 45 Wall & OH Internal Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
7241410 45 Wall & OH External Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
7241411 45 Post Internal Mount 316 Stainless Steel 22.2 (5,000) 0.8 (180)
7241525 90 Wall External Corner Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
7241526 90 Wall Internal Corner Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
7241570 45 Wall Internal/External Corner Mount 316 Stainless Steel 38 (8,540) 0.8 (180) or 5 (1,125)
Maximum Entry/Exit Angle: The maximum angle at which the HLL cable can enter or exit each Corner Bracket is 15°.
TRAVELER SPECIFICATIONS:
Figure 1 Part Number Description Material
Minimum Breaking
Strength kN (lb) Capacity
G
7241420 Detachable Traveler - No Wheels Stainless Steel 22.2 (5,000) 1 Person up to 140 kg (310 lbs)
including clothing, tools, etc.
per Traveler
7241421 Overhead Traveler Stainless Steel 22.2 (5,000) 1 Person up to 140 kg (310 lbs)
including clothing, tools, etc.
per Traveler
SYSTEM SPECIFICATIONS:
Anchorage Structure supporting the 8mm Permanent Horizontal Lifeline System must be analyzed and verifi ed by the Certifi ed Installer
1
for the resulting loads based on the system confi guration, energy absorbing component, and number of users.
Capacity 1 Person up to 140 kg (310 lbs) including clothing, tools, etc. per Traveler unless otherwise specifi ed by the documentation
from the Certifi ed Installer or on the System Tag. The Certifi ed Installer documentation will also specify the total number of
users allowed per system.
Operating
Temperature
-50° C - 120° C
(-58° F - 248° F)
Standards EN 795:2012 Class C, CENTS 16415:2013 Class C, OSHA 1926.502, AS/NZS 1891.2:2001, ANSI Z359.6
2
, and CSA Z259.16
2
TOOL SPECIFICATIONS:
Tensioning
Tools
All 8 mm Lifelines: Tensioning Tool, 3M Part 7241431
0.8 kN (180 lbf) Tensioned Lifelines: Drill Driver
5 kN (1,125 lbf) Tensioned Lifelines (General Use): Impact Driver with 165 Nm (120 lbf-ft) Minimum Torque
5 kN (1,125 lbf) Tensioned Lifelines (Heavy Use): Impact Driver with 300 Nm (220 lbf-ft) Minimum Torque
Swaging
Tools
Hex Swage Dies: 10 mm Bite, 3M Part 7241122 Recommended
Hand Compression Tool (Swager): 38 kN (8,543 lbf) Minimum Swage Strength
Power Compression Tool (Power Swager): Milwaukee M18™ Force Logic™ 12 Ton Utility Crimper, PN 2778-22 (or
equivalent 12 Ton Power Swager):
Swage Test Tool: 7241126 Cable and Eyebolt Tester Kit
1 3M Certifi ed Installer: A person certifi ed by 3M with extensive knowledge, training, and experience in the fall protection and rescue fi eld who is capable of designing,
analyzing, evaluating, and specifying fall protections and rescue systems to the extent required by applicable regional and national standards.
2 ANSI Z359.6, CSA Z259.16: This system meets these design requirements when designed by a professional and is inclusive of a full documentation package as
specifi ed in ANSI Z359.6 or CSA Z259.16.
To Next Page
Loading...
