3M X20 Product Safety Guide

3M™ Multimedia Projector X20 Product Safety Guide© 3M 2006 11
ENGLISH
• To reduce the risk associated with exposure to hazardous voltage:
- Disconnect power cord when the projector is not in use, during lamp replacement,
and while cleaning.
-
'RQRWUHPRYHDQ\VFUHZVRWKHUWKDQWKRVHVSHFL¿HGLQWKHODPSUHSODFHPHQWLQVWUXFWLRQV
- Do not attempt to service the projector - there are no user serviceable parts, other
than the lamp cartridge, inside the projector. Contact a 3M authorized service
provider for service.
• To reduce the risk associated with hot surface of lamp cartridge:
- Unplug the projector from the electrical outlet and allow the lamp to cool for 45
minutes before replacing the lamp.
• To reduce the risk associated with a ruptured lamp:
- Always handle the fragile lamp module with care.
- Remove the projector from the ceiling or wall mount before replacing the lamp. In
the case of a lamp rupture, small glass particles could fall out when the lamp door
is opened or the projector is tilted.
- Use care when replacing the lamp module in the event of a lamp rupture - small
glass particles and small amounts of mercury may be present.
- Ventilate the area where the lamp rupture occurred.
- Wear safety goggles and gloves when cleaning up ruptured lamp debris.
-
Carefully collect the ruptured lamp debris in a closed container and dispose of the container
and the expired lamp module in accordance with federal, state, and local regulations.
- Wash your hands thoroughly after handling ruptured lamp debris.
- Replace the lamp module when the lamp replacement message appears.
- Never replace the lamp module with a previously used lamp module.
• To reduce the risk associated with environmental contamination due to
mercury in the projection lamp:
-
Dispose of lamp cartridge in accordance with applicable federal, state and local regulations.
- The lamp in this product contains mercury. Dispose of projection lamp in a manner
that is consistent with your local hazardous waste regulations for mercury.
- For recycling and disposal information, contact your respective governmental
agencies.
In U.S., contact the Electronic Industries Alliance at www.lamprecycle.org
In Canada, contact 1-800-362-3577 (3M Canada)
WARNING
The glass lamp used in this projector contains small amounts of mercury and operates at
high pressure and at high temperature and may unexpectedly shatter. Each lamp has a
different lifetime and can fail in different ways, including a rupture with a loud bang or
simply burn out. In the event of a lamp rupture, be sure to follow the instructions.
Replacing Lamp
Important Note:
,IWKHODPSEUHDNVVRRQDIWHUWKH¿UVWWLPHLWLVXVHGLWLVSRVVLEOHWKDWWKHUHDUHHOHFWULFDOSUREOHPV
elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

3M X20 Specifications

General

Number of colors	16.78 million colors
Vertical scan range	56 - 120 Hz
Horizontal scan range	31.5 - 106 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	300 \
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-30 - 30 °
Audio input	1
Aspect ratio	4:3, 16:9
Dimensions (WxDxH)	274 x 205 x 59 mm
Power requirements	100 - 120 V, 220 - 240 V, 50/60 Hz
Focus	Manual
Focal length range	16.4 - 19.7 mm
Lamp type	UHB
Lamp power	160 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Analog signal format system	NTSC, NTSC 4.43, PAL, SECAM
RMS rated power	1 W
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Noise level	36 dB
Certification	UL, cUL, FCC Part 15 Class B, CE, EN60950, WEEE
Power consumption (typical)	250 W
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	5 - 35 °C

Weight and Dimensions

Weight	1784 g