ABB ACS880-14 - Page 169

Parameters 169
14.06 DIO delayed status (Visible when 14.01 Module 1 type = FIO-01 or FIO-11)
Displays the delayed status of the digital input/outputs on the
extension module. This word is updated only after
activation/deactivation delays (if any are specified).
Bit 0 indicates the status of DIO1.
Note: The number of active bits in this parameter depends on
the number of digital input/outputs on the extension module.
Example: 1001b = DIO1 and DIO4 are on, remainder are off.
This parameter is read-only.
-
0000b…1111b Delayed status of digital input/outputs. 1 = 1
14.08 DI filter time (Visible when 14.01 Module 1 type = FDIO-01)
Defines a filtering time for parameters 14.05 DI status and
14.06 DI delayed status.
10.0 ms
0.8 … 100.0 ms Filtering time for DI status parameters. 10 = 1 ms
14.08 DIO filter time (Visible when 14.01 Module 1 type = FIO-01 or FIO-11)
Defines a filtering time for parameters 14.05 DIO status and
14.06 DIO delayed status. The filtering time will only affect the
DIOs that are in input mode.
10.0 ms
0.8 … 100.0 ms Filtering time for DIO status parameters. 10 = 1 ms
14.09 DIO1 function (Visible when 14.01 Module 1 type = FIO-01 or FIO-11)
Selects whether DIO1 of the extension module is used as a
digital input or output.
Input
Output DIO1 is used as a digital output. 0
Input DIO1 is used as a digital input. 1
14.11 DIO1 output source (Visible when 14.01 Module 1 type = FIO-01 or FIO-11)
Selects a drive signal to be connected to digital input/output
DIO1 of the extension module when parameter 14.09 DIO1
function is set to Output.
Not
energized
Not energized Output is not energized. 0
Energized Output is energized. 1
Ready run Bit 1 of 06.11 Main status word (see page 131). 2
Enabled Bit 0 of 06.16 Drive status word 1 (see page 132). 4
Started Bit 5 of 06.16 Drive status word 1 (see page 132). 5
Magnetized Bit 1 of 06.17 Drive status word 2 (see page 133). 6
Running Bit 6 of 06.16 Drive status word 1 (see page 132). 7
Ready ref Bit 2 of 06.11 Main status word (see page 131). 8
At setpoint Bit 8 of 06.11 Main status word (see page 131). 9
Reverse Bit 2 of 06.19 Speed control status word (see page 135). 10
Zero speed Bit 0 of 06.19 Speed control status word (see page 135). 11
Above limit Bit 10 of 06.17 Drive status word 2 (see page 133). 12
Warning Bit 7 of 06.11 Main status word (see page 131). 13
Fault Bit 3 of 06.11 Main status word (see page 131). 14
Fault (-1) Inverted bit 3 of 06.11 Main status word (see page 131). 15
Start request Bit 13 of 06.16 Drive status word 1 (see page 132). 16
Open brake
command
Bit 0 of 44.01 Brake control status (see page 328). 22
Ext2 active Bit 11 of 06.16 Drive status word 1 (see page 132). 23
No. Name/Value Description Def/FbEq16