ABB DCS 600 MultiDrive User Manual (English)

Other manuals for ABB DCS 600 MultiDrive

Questions and Answers:

S
stacie37Aug 15, 2025
What to do if ABB Media Converter shows speed feedback fault?
- S
  stevenkellerAug 16, 2025
  If the ABB Media Converter displays a speed feedback fault, check the incremental encoder and connection cable, ensuring the encoder power supply provides adequate feedback. Verify the tacho polarity and voltage, and confirm the position of jumper S4 on board SDCS-CON-2. Inspect the electronic boards SDCS-CON-2, SDCS-IOB-3, and SDCS-POW 1. Also, check the connection between the converter and the armature circuit for any open connections. Finally, confirm the correct setting for the selection of speed feedback monitoring.
W
William RobinsonAug 18, 2025
What causes ABB Media Converter to display an overcurrent?
- L
  Lisa DyerAug 19, 2025
  An overcurrent error on the ABB Media Converter can be caused by faults or blocking conditions in the motor, load, and armature cabling. It can also result from incorrect parameter settings in the current control circuit or torque limitation, or the parameter [P 42.05] (overcurrent detection). A faulty thyristor could also be the cause. Therefore, check the motor, load, and armature cabling for faults or blocking conditions, and the parameter settings of the current control circuit, the torque limitation, and parameter [P 42.05]. Also, check the thyristor.
P
Patricia NicholsAug 21, 2025
What should I do if ABB Media Converter shows auxiliary voltage fault?
- J
  john85Aug 21, 2025
  If the ABB Media Converter indicates an auxiliary voltage fault, it means the auxiliary voltage (230 V) is too low during operation. Check internal auxiliary voltages. If the fault persists, replace the SDCS-CON-2 and/or SDCS-POW 1 board, if necessary.
M
Michael WhiteAug 25, 2025
How to troubleshoot earth fault in ABB DCS 600 MultiDrive?
- M
  Megan DunnAug 26, 2025
  To troubleshoot an earth fault in the ABB Media Converter, disconnect the mains and verify zero voltage in the armature and field circuits. Perform an insulation test for the complete installation. Check the sum current transformer; if necessary, replace the transformer and the SDCS-IOB-3 board.
J
Jared WallaceAug 28, 2025
What to check if ABB Media Converter reports overtemperature of MOTOR 1?
- M
  marshalleileenAug 28, 2025
  If the ABB Media Converter is reporting overtemperature of MOTOR 1, check the temperature sensor and its cabling. Also, check the motor cooling and sizing, the inputs for the temperature sensor on board SDCS-IOB-3, and ensure the parameter setting [P 28.11] is correct.
S
Steven DavisAug 30, 2025
What to check if ABB DCS 600 MultiDrive Media Converter reports overload of MOTOR 1?
- J
  joshua92Aug 30, 2025
  If the ABB Media Converter reports an overload of MOTOR 1, you should check the motor temperature (let the motor cool down before restarting). Also, verify the motor ratings and parameters of the thermal model, the motor sizing or load cycle, and ensure that parameter setting [P 28.04] is correct.
B
Brittney StephensSep 2, 2025
What to check if ABB Media Converter reports overtemperature of MOTOR 2?
- J
  Jessica ThomasSep 2, 2025
  If the ABB Media Converter reports overtemperature of MOTOR 2, check if the parameter setting [P 28.14] is correct.
B
Bradley EllisSep 5, 2025
What to check if ABB DCS 600 MultiDrive reports overload of MOTOR 2?
- M
  Melissa SmithSep 6, 2025
  If the ABB Media Converter indicates an overload of MOTOR 2, verify the motor is not overloaded and check if the parameter setting [P 28.07] is correct.
J
james78Sep 9, 2025
What to do if ABB DCS 600 MultiDrive Media Converter shows overcurrent converter fan only in combination on 42.14?
- K
  Kenneth ChavezSep 9, 2025
  If the ABB Media Converter shows an overcurrent related to the converter fan, check the settings for the current converter fan (PW 1002 / PW 1003), parameter [P 42.19], parameter [P 42.14], and monitor [4.14].
M
Michael DavisSep 12, 2025
How to fix 'no control program in memory' error on ABB DCS 600 MultiDrive?
- C
  Christopher CarterSep 12, 2025
  To resolve a 'no control program in memory' error on the ABB Media Converter, load the firmware again.