ABB MINI-MAG 10D1475 Series

To Next Page

To Previous Page

Vibration Limit

Integrally Mounted *5 to 14 Hz, 0.10 inch,

14 to 2000 Hz, 1 g

Signal converter must be remotely mounted if

these limits are exceeded.

Remotely Mounted 5 to 14 Hz, 0.20 inch

14 to 2000 Hz, 1.5 g

Materials of Construction

Meter Liner TEFZEL (ETFE)

Electrode Assemblies Hastelloy-C, Tantalum, Zirconium or Platinum

materials as specified (ref: Application Guide

PMI IV.C.10)

Meter Housing carbon steel, all welded construction, epoxy finish

Electronics Housing die cast aluminum, epoxy finish, 316 sst attach-

ment screws, 1/2 in. NPT conduit connections;

gasketed covers

Installation Kit includes 2 gaskets, mounting studs and nuts,

flange adaptor device when required.

Safety Classification Refer to Section 1.2

10D1475 MINI-MAG MAGNETIC FLOWMETER INSTRUCTION MANUAL

INTRODUCTION 1-9

Main Page

Table of Contents3
Safety Summary6
Read First10
Introduction12
General12
Model Number Breakdown14
Specifications17
Table 1-1. Meter Capacity17
Table 1-2. Meter Weights19
Installation21
Inspection21
Location21
Mounting22
Meter Orientation22
Meter Handling22
Pipe Connections26
Figure 2-4. Recommended Piping Arrangement26
Figure 2-5. Bolt Tightening Sequence27
Table 2-1. Recommended Mounting-Bolt Torques27
Gaskets28
Basic Mounting Procedure28
Figure 2-6. Meter Mounting Diagram29
Grounding Procedure30
General30
Conductive Pipeline30
Figure 2-7. Grounding Procedure, Conductive Pipe31
Non-Conductive or Insulated Pipeline32
Figure 2-8. Outline Dimensions, Grounding Rings32
FIGURE 2-9. GROUNDING PROCEDURE, NON-CONDUCTIVE or INSULATED PIPE33
Electrical Interconnections34
Conduit Seal and Pressure Relief34
Figure 2-10. Interconnection Wiring Blocks34
Figure 2-11. Conduit Entry Seal Installation35
Start-Up36
Preliminary Check List36
Figure 3-1. Typical Integral Primary 10D1475J Data Tag36
Turn Power on37
Zero Check37
Detector Empty Pipe (Option)37
Start Process Flow37
Electronics38
FIGURE 3-3. 1/10 through 3/8 INCH INTEGRAL/REMOTE ENCLOSURE [10D1475S]38
FIGURE 3-4. 1/2 through 4 INCH INTEGRALLY MOUNTED ENCLOSURE WITHOUT39
Functional Description42
Basic Operating Principle42
Signal Voltage Generation42
Figure 4-1. Basic Operating Principle42
Magnet Coil Drive Circuits43
Volumetric Flow Rate Measurement43
Operating Characteristics44
Liquid Variables44
Liquid Conductivity44
Liquid Temperature45
Other Liquid Variables45
Metering Characteristics45
Circuit Description46
Primary Signals46
Constant Meter Capacity (CMC) PC Assembly46
Jumper Selections47
Model 10D1475S47
Model 10D1475J47
Integral47
Remote49
Maintenance50
General50
System Troubleshooting51
Static Test52
Magnet Coil Check52
Table 5-1. Primary Coil Resistance52
Electrode Check53
Flowmeter Board53
Parts54
Grounding Rings54
Gaskets54
Table 6-1. Ansi Class 150 Grounding Rings54
Table 6-2. Gaskets for Ansi Class 150 Grounding Rings54
Adapter Sleeves55
Table 6-4. Adapter Sleeve55
Table 6-3. Gaskets for Meter Body55
Studs & Nuts56
Cable Entry Seals56
Conduit Entry Seal56
Cable Entry Seal56
Table 6-5. Studs & Nuts56

ABB MINI-MAG 10D1475 Series - Page 20

Table of Contents

Related product manuals