ABB REF601 - Configurable Binary Inputs

1
MDU07212
REF601 / REJ601
Application Manual
4.13
MDU07212
REF601 / REJ601
Application Manual
4.13
MDU07212
REF601 / REJ601
Application Manual
4.13
MDU07212
-
YN
REF601 / REJ601
Application Manual
YN
Rev. C
REF601 / REJ601
Application Manual
Rev. C
REF601 / REJ601
Application Manual
Rev. C
Table
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
1.
The function configured for blocking will remain in block state until BI1 is active.
2.
3.
Table
LED
Ready (Green)
Start (Yellow)
Trip (RED)
LED 1 (RED)
LED 2 (RED)
LED 3 (RED)
LED 4
LED 5
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
1.
The function configured for blocking will remain in block state until BI1 is active.
2.
3.
Table
2
2
LED
Ready (Green)
Start (Yellow)
Trip (RED)
LED 1 (RED)
LED 2 (RED)
LED 3 (RED)
LED 4
LED 5
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
with open circuit
The function configured for blocking will remain in block state until BI1 is active.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
communication.
Circuit Breaker C
provide external (remote) breaker open or breaker close command.
2
:
Ready (Green)
Start (Yellow)
Trip (RED)
LED 1 (RED)
LED 2 (RED)
LED 3 (RED)
(RED)
(RED)
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
with open circuit
The function configured for blocking will remain in block state until BI1 is active.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
communication.
Circuit Breaker C
provide external (remote) breaker open or breaker close command.
LED indications (on relay front))
Ready (Green)
Start (Yellow)
Trip (RED)
LED 1 (RED)
LED 2 (RED)
LED 3 (RED)
(RED)
(RED)
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
with open circuit
The function configured for blocking will remain in block state until BI1 is active.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
communication.
Circuit Breaker C
provide external (remote) breaker open or breaker close command.
LED indications (on relay front))
Ready (Green)
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
with open circuit
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
binary input.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
communication.
Circuit Breaker C
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
output to r
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
User configured:
Default:
User configured:
Default:
User configured:
Default:
User configured:
Default: Spare (not configured)
User configured:
Default: Spare (not configured)
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
with open circuit
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
binary input.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
communication.
Circuit Breaker C
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
output to r
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
User configured:
Default:
User configured:
Default:
User configured:
Default:
User configured:
Default: Spare (not configured)
User configured:
Default: Spare (not configured)
Configurable Binary Inputs
The IED has four binary
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
with open circuit
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
binary input.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
communication.
Circuit Breaker C
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
output to r
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
User configured:
Default:
Trip I
User configured:
Default:
Trip I
User configured:
Default:
TCS Fault
User configured:
Default: Spare (not configured)
User configured:
Default: Spare (not configured)
Configurable Binary Inputs
The IED has four binary
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
binary input.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
Circuit Breaker C
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
output to r
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
User configured:
Trip I
User configured:
Trip I
User configured:
TCS Fault
User configured:
Default: Spare (not configured)
User configured:
Default: Spare (not configured)
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
binary input.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
output to r
eceive respective command.
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
User configured:
Trip I
p
=>
User configured:
Trip I
o
=>
User configured:
TCS Fault
User configured:
Default: Spare (not configured)
User configured:
Default: Spare (not configured)
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
User configured:
=>
Trip overcurrent faults (I>, I>> and I>>>)
User configured:
=>
Trip earth faults (I
User configured:
TCS Fault
=>
User configured:
Default: Spare (not configured)
User configured:
Default: Spare (not configured)
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
for binary input BI2 to BI4, user
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
LED indications (on relay front))
Default configuration
LED indicates that relay
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
Trip earth faults (I
=>
trip circuit has failure
Default: Spare (not configured)
Default: Spare (not configured)
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
LED indicates that relay
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
Trip earth faults (I
trip circuit has failure
Default: Spare (not configured)
Default: Spare (not configured)
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
breaker position.
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
Trip earth faults (I
trip circuit has failure
Default: Spare (not configured)
Default: Spare (not configured)
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
Trip earth faults (I
trip circuit has failure
Configurable Binary Inputs
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Start LED for any protection function
start
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
Trip earth faults (I
o
> and I
trip circuit has failure
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
operation, it is not available for other operation.
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
block breaker opening and closing command
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
start
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
> and I
trip circuit has failure
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
> and I
o
>>
trip circuit has failure
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
eceive respective command.
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
>>
)
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
individual protection functions viz., I>, I>>, I>>>, Io> and I
o
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Common trip LED for overcurrent and earth fault trip indication
Trip overcurrent faults (I>, I>> and I>>>)
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
o
>> as well as to
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Section 4
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
to glow until power goes off or there is internal fault in the relay
Common trip LED for overcurrent and earth fault trip indication
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
>> as well as to
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Section 4
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
function. User depending on his need can configure this binary input to block
>> as well as to
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
maintenance. The available status information is sent to MODBUS
ommand: Binary inputs BI2 to BI4 can be configured to
provide external (remote) breaker open or breaker close command.
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Section 4
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
Blocking: Binary input BI1 is dedicate for blocking protection and cont
rol
function. User depending on his need can configure this binary input to block
>> as well as to
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
ommand: Binary inputs BI2 to BI4 can be configured to
For routing circuit breaker opening or closing command from
binary input, it is necessary that user also configures binary
Section 4
Protection and Control Function
has no internal fault and is powered up for desired
functionality. It glows after internal health check after power on and continue
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
input i.e., once any of the binary input BI2 to BI4 is configured for a particular
rol
function. User depending on his need can configure this binary input to block
>> as well as to
and trip circuit supervision e.g
The function configured for blocking will remain in block state until BI1 is active.
BI1 configured to block breaker opening and closing command
will block command received from local HMI or MODBUS or
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
the status of circuit breaker i.e. breaker open or breaker close or breaker in
ommand: Binary inputs BI2 to BI4 can be configured to
Section 4
Protection and Control Function
35
inputs BI1 to BI4. Each binary input can be configured
individually and supports various features. Binary input BI1 is fixed for blocking
operation, whereas BI2 to BI4 are used for other than blocking operation. However
at a time can configure one operation per binary
function. User depending on his need can configure this binary input to block
>> as well as to
and trip circuit supervision e.g
.
The function configured for blocking will remain in block state until BI1 is active.
Circuit Breaker Status: Binary inputs BI2 to BI4 can be configured to indicate
Section 4
Protection and Control Function
35
operation, whereas BI2 to BI4 are used for other than blocking operation. However