ABB TPS57-D Series - User Manual

130 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operation Manual

Turbocharging

ABB Turbo Systems Ltd



ABB Turbo Systems Ltd

CH 5401 Baden

Type TPS 48E01 HT562672

n

Mmax

1000 t

Mmax

680

n

Bmax

950 t

Bmax

650

1/s °C

SOLD08 00180 12 60 60

Year 2013

made in Switzerland

Application according to

the Operation Manual

kg

HZTL2410 English

TPS 48E01

Original Operation Manual

Table of Contents

Questions and Answers

K
Katherine BerrySep 15, 2025
What to do if there is a reduction in speed of ABB Battery Charger?
- C
  Corey HunterSep 15, 2025
  If your ABB Battery Charger experiences a reduction in speed, there might be several reasons. It could be due to defects of connected cylinders when pulse charging, which requires contacting the enginebuilder. Another cause might be heavy contamination of the turbine, which requires cleaning. Damaged rotor components or bearing also can cause the problem, and in this case you should contact an ABB Turbocharging Service Station. Finally, defects such as leaks in the exhaust gas pipes or charge air ducts can lead to speed reduction, and these should be repaired.
O
omunozAug 25, 2025
Is rubbing of rotating parts in ABB Industrial Equipment a problem?
- B
  Brian McgrathAug 25, 2025
  Rubbing of rotating parts in ABB Industrial Equipment can be normal behavior and not a malfunction. However, if there is any doubt about the extent of rubbing, then an ABB Turbocharging Service Station must be contacted.
R
Rose ForbesAug 25, 2025
What to do if rotating parts are rubbing in ABB TPS57-D?
- J
  jasonsimmonsAug 26, 2025
  If you suspect rubbing of rotating parts within your ABB Industrial Equipment, and there is any doubt about the extent of rubbing, then an ABB Turbocharging Service Station must be contacted.
P
Patrick SkinnerAug 26, 2025
What to do if ABB TPS57-D Industrial Equipment has rubbing of rotating parts?
- R
  Robert FrederickAug 26, 2025
  If you suspect rubbing of rotating parts in your ABB Industrial Equipment, and you're unsure about the extent of the rubbing, it's best to contact an ABB Turbocharging Service Station. They can perform a dimension check to assess the situation.
R
rhallSep 16, 2025
Why is the lubricating oil pressure too low in my ABB Battery Charger?
- J
  jimenezjenniferSep 16, 2025
  If the lubricating oil pressure is too low in your ABB Battery Charger, it could be due to several reasons. The oil filter might be heavily contaminated, which means it should be cleaned. Another possibility is a defective oil pump in the lubricating system, which needs to be checked or replaced. The manometer display could be wrong, requiring replacement of the manometer. Alternatively, the rotor axial clearance might be too large, which requires contacting an ABB Turbocharging Service Station.
C
Chelsea SnyderSep 23, 2025
What to do if ABB Battery Charger has vibrations?
- J
  Jordan TurnerSep 23, 2025
  If you're experiencing vibrations with your ABB Battery Charger, it's likely due to rotor unbalance. In this case, you should contact an ABB Turbocharging Service Station.
R
rodneyfreySep 8, 2025
What causes charge air pressure to be too high in ABB Battery Charger?
- J
  Justin MooreSep 8, 2025
  If the charge air pressure of your ABB Battery Charger is too high, it could be due to a malfunctioning or poorly adjusted injection system. You should repair it or contact the manufacturer, or correct it.
M
madisonjonesSep 9, 2025
Why ABB Battery Charger makes noises during run-down?
- R
  richard31Sep 9, 2025
  If your ABB Battery Charger is experiencing noises during run-down, the turbocharger may be contaminated, requiring cleaning. Alternatively, there may be a damaged bearing, in which case you should contact an ABB Turbocharging Service Station.
L
Lori BeckerSep 2, 2025
What to do if ABB Battery Charger is surging?
- J
  Jason FullerSep 3, 2025
  If your ABB Battery Charger is experiencing turbocharger surging, the guard in front of the turbocharger may be contaminated or damaged, requiring cleaning or replacement. Alternatively, the filter silencer or diffuser could be contaminated, in which case you should clean it. Another possibility is a contaminated cooler, which would also need cleaning.
J
Jessica HaysAug 31, 2025
What to do if ABB Industrial Equipment is vibrating?
- J
  Joseph AndersonSep 1, 2025
  If your ABB Industrial Equipment is vibrating, it may be due to rotor unbalance. In this situation, contact an ABB Turbocharging Service Station.

ABB TPS57-D Series Specifications

General

Brand	ABB
Model	TPS57-D Series
Category	Industrial Equipment
Language	English

Related product manuals

ABB TPS57 Series

ABB TPS57-F Series

ABB TPS52 Series

ABB TPS52-D Series

ABB TPS48 Series