••.cam
•
To
ensure the Quadcopter successfully flies
back
to the Home Point when it is
in
Failsafe mode, please take-off only after the Quadcopter's GPS successfully
connects to the satellite.
• The
Quad
copter cannot automatically avoid obstacles
in
ils path when it is flying
in
Failsafe mode.
4.3 How to regain control
on
the Transmitter
When the Quadcopter is oul
of
control, toggle lhe S4 switch on the transmitter several times
to
switch flight mode. When the signal is restored, the transmitter will
regain control,
and
you can continue to use the transmitter to operate the Quadcopter.
5 Battery Level Alarm
Function
When Quadcopter Battery Power Is
low,
It
has
lnsuflldent Power
and
you must land It as soon as possible,
or
else
It
may lose Power completely and crash,
damaging
the
Quadcopter
or
create a dangerous situation.
In
order to prevent danger caused
by
low Battery, the Quadcopter has a two-level Battery
alanm
function.
Level1 is a Low Power alarm and Level 2 is a Severe
Low
Power
alanm
that is indicated by the flight indicator lights.
Low
Power
alanm
Flight
Indicator
light
statUI
Low
Powsr
rllk
prompt
2 Front Indicator and 2 Rear Indicator Slow Blink
In level
1
alanm
condition, Quadcopter flies normally for few minutes
and
then initiates
level
1 alarm Level 2 alarm. Be cautious while flying, keep the Quadcopter within sight and
do
not to fty
(blinks
on
and off
in
1s intervals}
too
high
or
too far.
In level 2 alarm condition, Quadcopter flies normally for few minutes and then initiates
Level 2 alarm
2 Front Indicator 2 Rear Indicator Fast Blink (blinks Failsafe mode
and
commences
to
automatically land. Under such a situation, please
twice within 1s}
return and land the Quad copter as safely as possible, and do not push the throttle hard
or
make
big
movements during flight.
During
low-Power automatic landing, you
can
regain control
of
the Quadcopter by switching the flight mode. However,
do
not do
so
repeatedly, as it
may:
1} Reduce battery service life due to over discharge.
2) Quadcopter may crash due to lnsuflldent Power.
Using AEE
AP
APP
The AEE
AP
APP Is primarily used to control the
Quad
copter Camera. It can be used to configure video and Camera parameters, control the Camera angle and
capture images
and
videos.
It
can also display Quadcopter status parameters.
1 Download and Install AEE
AP
APP
To
use
the AEE AP APP, please download the app and install it on your smart device.
Please ensure your smart devices is conneclad to the internet, enter the "App Store", type
"AEE
AP • in the search field and search.
You
will find the application icon
shown in the search
results and follow the prompts to complete installation.
2 Connect
to
AP1
0 System Network
Before you start using the
APP,
you
need
to
connect to the
AP1
0 system network. The specific procedures are as
follows:
Navigate to smart devices "Settings"- "Wi-Fi" page. Locate the •
AEE_AF-""
network
in
the "Select Network" list.
Select this network, enter the password (default password
Is
"AEE12345"), and connect.
• Please make sura that cell phone close to the Wi-Fi repeater
in
order to get better performance
of
video transmission
NO
SIM
--
<
Se
ttings
Wl
·
FI
Wi·FI
CHOOSE A NETWORK ...
aee-ceo
i
...
<D
~r
·
fl03-oew
i
...
<D
0702
i
...
<D
AEE
_A
P*
***
i .
<D
Othe
r
...
18
To Next Page
Loading...
