SCPI Commands Appendix B
Model N6705 User’s Guide 195
These settings are set by the Reset (*RST) command
OUTPut:PMODe VOLT SENSe:SWEep:POINts 1024 or 4883
OUTPut:PROTection:COUPle OFF SENSe:SWEep:OFFSet:POINts 0
OUTPut:PROTection:DELay 0.02 SENSe:SWEep:TINTerval 20.48E−6
OUTPut:PROTection:OSCillation ON SENSe:SWEep:TINTerval:RESolution RES20
OUTPut:PROTection:WDOG OFF SENSe:VOLTage:RANGe MAX
OUTPut:RELay:POLarity NORM SENSe:VOLTage:RANGe;AUTO OFF
OUTPut:TMODe LOWZ SENSe:WINDow RECT
POWer:LIMit MAX STEP:TOUTput FALSE
RESistance 0 TRIGger:ACQuire:CURRent MIN
RESistance:STATe OFF TRIGger:ACQuire:CURRent:SLOPe POS
SENSe:CURRent:CCOMpensate ON TRIGger:ACQuire:SOURce BUS
SENSe:CURRent:RANGe:AUTO OFF TRIGger:ACQuire:VOLTage MIN
SENSe:DLOG:CURRent:RANGe:AUTO OFF TRIGger:ACQuire:VOLTage:SLOPe POS
SENSe:DLOG:FUNCtion:CURRent OFF TRIGger:ARB:SOURce IMM
SENSe:DLOG:FUNCtion:MINMax OFF TRIGger:DLOG:CURRent MIN
SENSe:DLOG:FUNCtion:VOLTage ON TRIGger:DLOG:CURRent:SLOPe POS
SENSe:DLOG:OFFset 0 TRIGger:DLOG:SOURce IMM
SENSe:DLOG:TINTerval 0.1 TRIGger:DLOG:VOLTage MIN
SENSe:DLOG:TIME 30 TRIGger:DLOG:VOLTage:SLOPe POS
SENSe:DLOG:VOLTage:RANGe:AUTO
SENSe:ELOG:CURRent:RANGe:AUTO OFF TRIGger:HISTogram:SOURce BUS
SENSe:ELOG:FUNCtion:CURRent ON TRIGger:TRANsient:SOURce BUS
SENSe:ELOG:FUNCtion:CURRent:MINMax OFF VOLTage MIN
SENSe:ELOG:FUNCtion:VOLTage OFF VOLTage:BWIDth LOW
SENSe:ELOG:FUNCtion:VOLTage: MINMax OFF VOLTage:LIMit MAX
SENSe:ELOG:PERiod 0.1 VOLTage:LIMit:COUPle ON
SENSe:ELOG:VOLTage:RANGe:AUTO OFF VOLTage:LIMit:NEGative MIN
SENSe:FUNCtion “VOLT” VOLTage:MODE FIX
SENSe:FUNCtion:CURRent OFF VOLTage:PROTection:DELay 0
SENSe:FUNCtion:VOLTage ON VOLTage:PROTection:REMote MAX
SENSe:FUNCtion:VOLTage:INPut MAIN VOLTage:PROTection:REMote:NEGative MIN
SENSe:HISTogram:CURRent:RANGe MAX VOLTage:RANGe MAX
SENSe:HISTogram:CURRent:RANGe:AUTO OFF VOLTage:SLEW 9.9E+37
SENSe:HISTogram:FUNCtion:CURRent
VOLTage:TRIGger MIN
To Next Page
Loading...
