INJECTION HAZARD
SPRAYING VAPORS + STATIC SPARKING CREATE FIRE/EX PLO SION
Always be sure all equipment, paint bucket and object being sprayed
are properly grounded. Always ground sprayer, gun, paint bucket,
and object being sprayed. Be sure gun is grounded through hose
con nec tion. Con nect grounding wire to a true earth ground.
NEVER spray in closed area Ventilation must be adequate to remove
NEVER keep ammable materials in spray area.
NEVER spray highly ammable liquids.
Use only high pressure conductive airless hoses with static wire ap-
NEVER SMOKE IN SPRAYING AREAS.
ALWAYS ensure properly maintained re extinquishing equipment is
FLUSHING & CLEANING CAN CREATE STATIC SPARKING IF DONE IMPROPERLY!!!!
NEVER spray solvents under pressure through spray tip.
FOLLOW PRESSURE RELIEF PROCEDURE and remove spray tip
USE LOWEST POSSIBLE PRESSURE when ushing and cleaning.
FLUSHING & CLEANING CAN CREATE STATIC SPARKING IF DONE IMPROPERLY!!!!
Fluids under high pressure from spray or leaks can penetrate the skin
and cause serious injury and the need for amputation.
point the spray gun at anyone or any part of the body.
put hand or ngers over the spray tip. Do not use rag over your
NEVER
put hand
or ngers
over the spray tip.
Do not use
rag
over your
NEVER
ngers. Paint will penetrate through material and into the ngers.
try to stop leaks with your hand or body.
NEVER try to stop leaks with your hand or body
.
NEVER
NEVER wipe off build up around spray tip. ALWAYS remove the tip from
the gun to clean it after following Pressure Relief Procedure!!
If any uid appears to penetrate your skin, get
ONCE. DO NOT TREAT AS A SIMPLE CUT.
Tell the doctor exactly what
uid was injected and have him read the following Note.
NOTE TO PHYSICIAN: Injection in the skin is a trau mat ic in ju ry.
important to treat the injury sur gi cal ly as soon as possible. DO NOT
Toxicity is a concern with some
exotic coatings in ject ed directly into the blood stream. Con sul ta tion with a
plastic surgeon or re con struc tive hand surgeon may be ad vis able.
ALWAYS set safety lock on the gun in "LOCKED" po si tion when not in use
and before servicing or cleaning.
DO NOT remove or modify any part of gun.
Check operation of gun safety devices before each use
HIGH PRESSURE SPRAY CAN CAUSE EXTREMELY SERIOUS INJURY.
Handle as you would a loaded rearm.
Learn and follow the PRESSURE RELIEF PROCEDURE. Read and understand all instruction manuals, tags, warnings, user
’s guides
and labels on machine before operating equipment. Order new labels if unreadable.
NEVER spray in vicinity of open ame or other source of ignitions such
as water heaters and furnaces.
ALWAYS locate the sprayer and electrical outlets in use at least 25
feet away from spray area in well ventilated area. Do not plug in any
electrical cores in spray area.
Follow the coating and solvent manufacturer’s safety precautions and
HALOGENATED HYDRO CARBON WARNING: NEVER use
halogenated hydrocarbon (HHC) solvents or paints that contain them
in this system. Some of the most common of these solvents are: Car-
bontetrachloride, Chlorobenzene, Dichloroethane, Dichloroethyl Ether
,
Ethylbromide, Ethylchloride, Tetrachloethane.
Consult your supplier to be sure.
Hold gun rmly against a metal waste container to reduce spark pos si bil i ty.
NEVER use cleaning solvents with ash points below 140 degrees F.
Some of these are: acetone, benzene, either, gasoline, naptha. Consult your
AIRLESSCO SL&LP SAFETY GUIDE
Use extreme caution when cleaning or chang ing spray tips. If the spray tip clogs
while spray ing, engage the gun safety latch and ALWAYS follow the
before removing the spray tip to clean it.
NEVER wipe off build up around the spray tip.
NEVER operate gun without tip guard attached
ALWAYS ensure switch is in “OFF” position before plug ging unit in.
ALWAYS ensure switch is in “OFF” position before plug ging unit in.
ALWAYS ensure unit is in prime position and spray gun locked before starting
NEVER alter equip ment in any manner.
NEVER spray highly ammable materials.
NEVER use around children or let children use sprayer.
NEVER allow another person to use sprayer.
ALWAYS wear a face mask while spraying.
NEVER leave sprayer unattended with pressure in system.
NEVER use weak or damaged nonconductive paint hose. Do not allow
kinking, crushing, or allow it to vibrate against rough, sharp or hot surfaces.
Check hoses for damage or wear before each use.
REPLACE DAMAGED HOSE - DO NOT mend with tape or any other device.
USE ONLY conductive or grounded uid hoses for airless ap pli ca tions.
TIGHTEN all uid con nec tions before each use.
AIRLESSCO SL&LP SAFETY GUIDE
AIRLESSCO SL&LP SAFETY GUIDE
AIRLESSCO SL&LP SAFETY GUIDE
AIRLESSCO SL&LP SAFETY GUIDE
PRESSURE RELIEF PROCEDURE
Learn this procedure before operating unit. Never attempt to change or clean spray tip or service unit
and gun without rst releasing the pressure by:
Lock gun trigger safety lock.
Release gun trigger safety lock & trigger gun into pail.
Turn Prime/Pressure Relief Valve open to relieve residual uid pressure.
If spray tip or hose is clogged, follow steps 1-5 & expect paint splashing into the bucket during Step 5.
To Previous Page
Loading...
