What to do if my AIRLESSCO SL810 Paint Sprayer is spraying too much material?
If your AIRLESSCO Paint Sprayer is spraying too much material, it could be due to a nozzle that is too large, material that is too thin, or pressure that is too high. Try using a smaller nozzle and reduce the pressure.
How to fix too little material coming from my AIRLESSCO Paint Sprayer?
If your AIRLESSCO Paint Sprayer is dispensing too little material, the nozzle might be too small, or the material might be too thick. Try using the next larger nozzle.
What to do if AIRLESSCO SL810 spray pattern is irregular?
An irregular or deflected spray pattern from your AIRLESSCO Paint Sprayer is often caused by a clogged orifice or a damaged tip. Carefully clean the tip, and if the problem persists, replace it with a new one.
How to fix coarse spray from AIRLESSCO SL810?
A coarse spray from your AIRLESSCO Paint Sprayer is often due to low pressure. Increase the pressure to achieve a finer spray.
How to correct a spray pattern that is too wide with AIRLESSCO SL810 Paint Sprayer?
If the spray pattern from your AIRLESSCO Paint Sprayer is too wide, it is likely because the spray angle is too large. Use a smaller spray angle tip.
Why is my AIRLESSCO SL810 Paint Sprayer causing excessive fogging?
Excessive fogging (overspray) from your AIRLESSCO Paint Sprayer can occur due to high pressure or if the material is too thin. To resolve this, reduce the pressure until you achieve a satisfactory pattern distribution. If the material is too thin, use less thinner.
How to unclog screens on AIRLESSCO Paint Sprayer?
Clogged screens in your AIRLESSCO Paint Sprayer can result from extraneous material in the paint, coarse pigments, or poorly milled pigments. To resolve this: * Clean the screen. * If the orifice size allows, use a coarse screen. * Use a coarser screen and larger orifice tips. * Obtain ball milled paint. If thinner has been added, test to see if a cover screen is present. Incompatible drops placed on top of the paint mix or flatten out on the paint mixture and thinners on the surface. If not, try a different thinner in a fresh batch of paint.
Why is a thick skin forming on my AIRLESSCO SL810 project?
A thick skin forming on your work when using the AIRLESSCO Paint Sprayer can be caused by material that is too viscous or an application that is too heavy. Thin the material cautiously, and reduce pressure or use a tip in the next smaller nozzle group.
Why is there thin distribution in the center of pattern “horns” with my AIRLESSCO SL810?
A thin distribution in the center of the pattern “horns” when using your AIRLESSCO Paint Sprayer is often caused by a worn or wrong tip. Change to a new tip, or use a nozzle with a narrow spray angle.
What to do if coating fails to close and smooth over with AIRLESSCO SL810?
If the coating fails to close and smooth over when using your AIRLESSCO Paint Sprayer, it is likely that the material is too viscous. Thin the material cautiously.
Medical alert for fluid injection injuries, emphasizing emergency care and physician notification.
High pressure fluids can penetrate skin, causing extreme injury, including amputation.
Keep area clear and ventilated, no flammable material or ignition sources.
Safety guidelines for gun operation, including tip guard and pressure relief.
Guidelines for checking, using, and maintaining high-pressure fluid hoses.
Ensure components have adequate pressure rating; follow pressure relief procedures.
Ground equipment, keep sprayer away from spray area, avoid plugging cords.
Serious injury or death from hazardous fluid/fumes. Know fluid hazards and use PPE.
Grounding sprayer and components to reduce static sparking risk.
Specific safety precautions for flammable materials, including ventilation and grounding.
Keep clear of moving parts to avoid amputation or burns.
Safety warning and instructions for grounding the sprayer and system components.
Step-by-step guide to starting the sprayer for operation.
Engage the gun safety latch as per the gun's manual.
Disengage safety latch and trigger gun to relieve pressure.
Open the Prime/Pressure Relief Valve to relieve remaining pressure.
Re-engage safety latch and close the Prime/Pressure Relief Valve.
Table listing common spray defects, their causes, and recommended corrections.
Troubleshooting steps for a unit that fails to prime.
Troubleshooting steps for low or no pressure after priming.
Troubleshooting steps for maintaining consistent spraying pressure.
Troubleshooting steps for a unit that does not run.
Verify control settings, circuit breaker, power source, and thermal overload.
Test motor brushes, sensor resistance, and thermal coupler continuity.
Test potentiometer and pressure control assembly for proper function.
Procedure to calibrate the zero point of the pressure display.
Procedure to calibrate the pressure reading against a gauge.
General| Brand | AIRLESSCO |
|---|---|
| Model | SL810 |
| Category | Paint Sprayer |
| Language | English |
To Next Page