Why Airwell GC 24 goes into protections?
If your Airwell Air Conditioner goes into protection mode and the compressor stops without a clear reason, it could be due to a control problem or a refrigeration system issue. Perform diagnostics and follow the actions described.
What to do if Airwell Air Conditioner outdoor fan does not work?
If your Airwell Air Conditioner compressor is running, but the outdoor fan isn't working, the problem could be with the outdoor electronics or the fan itself. Check the outdoor fan motor according to the procedure. If it's not working, replace the controller.
How to fix Airwell Air Conditioner power supply indicator?
If the power supply indicator (Red LED) on your Airwell Air Conditioner doesn't light up, it indicates a lack of power supply. Check the power supply. If the power supply is OK, check the display and display wiring. If that is OK, replace the controller.
General| Brand | Airwell |
|---|---|
| Model | GC 24 |
| Category | Air Conditioner |
| Language | English |
Provides a general description of the FLO DC Inverter split wall mounted range.
Highlights the key technological innovations and benefits of the FLO DCI series.
Details the features and specifications of the indoor units.
Outlines the features and installation aspects of the outdoor units.
Shows the compatibility between different indoor and outdoor unit models.
Provides detailed technical specifications for the FLO 18 DCI model.
Provides detailed technical specifications for the FLO 21 DCI model.
Provides detailed technical specifications for the FLO 24 DCI model.
Provides detailed technical specifications for the FLO 24 / GC 24 Z models.
Provides detailed technical specifications for the FLO 30 DCI model.
Defines the operational temperature and voltage limits for cooling and heating.
Graphical representation of the physical dimensions for indoor units.
Graphical representation of the physical dimensions for the GC 18 outdoor unit.
Graphical representation of the physical dimensions for the GC 21 outdoor unit.
Graphical representation of the physical dimensions for GC 24, GC 24 Z, GC 30 outdoor units.
Cooling and heating capacity data, power input, and correction factors for FLO 18/GC 18.
Cooling and heating capacity data, power input, and correction factors for FLO 21/GC 21.
Cooling and heating capacity data, power input, and correction factors for FLO 24/GC 24.
Cooling and heating capacity data, power input, and correction factors for FLO 24/GC 24 Z.
Cooling and heating capacity data, power input, and correction factors for FLO 30/GC 30.
Graphical representation of suction and discharge pressures versus outdoor temperature.
Octave band sound pressure level spectrum for indoor units FLO 18, 21, 24, 30.
Octave band sound pressure level spectrum for outdoor units GC 18, 21, 24, 30.
Details electrical power supply, current, and wiring requirements.
Schematics for indoor and outdoor unit wiring for FLO 18/21 DCI models.
Schematics for indoor and outdoor unit wiring for FLO 24 DCI models.
Schematics for the outdoor unit wiring for GC 24 Z model.
Schematics for indoor and outdoor unit wiring for FLO 30/GC 30 DCI models.
Diagrams illustrating the refrigeration cycle for heat pump models.
Diagrams showing electrical connection points for FLO 18/21 DCI.
Diagrams showing electrical connection points for FLO 24/30 DCI.
Explains the basic operational logic and parametric settings of the DCI software.
Details the NLOAD setting and compressor frequency management.
Describes how target compressor frequency is set based on NLOAD and temperature.
Explains the control logic for indoor fan speeds in different modes.
Details the control routines for outdoor fan speed based on operating conditions.
Lists and describes various protection mechanisms like defrost and overheating.
Common failures, probable causes, and corrective actions for specific outdoor units.
Explains how to enter diagnostics and interpret fault codes for indoor units.
Common failures, probable causes, and corrective actions for specific outdoor units.
Procedure to diagnose faults and interpret LED indicators for outdoor units.
Steps to check critical components like voltage, fuses, motors, and sensors.
Diagram showing disassembled parts of FLO 18/21 DCI indoor units.
Diagram showing disassembled parts of GC 18 DCI outdoor unit.
Diagram showing disassembled parts of GC 21 outdoor unit.
Diagram showing disassembled parts of FLO 24 DCI indoor unit.
Diagram showing disassembled parts of FLO 30 DCI indoor unit.
Diagram showing disassembled parts of GC 24, GC 30 outdoor units.
Diagram showing disassembled parts of GC 24 Z outdoor unit.
Reference to separate installation and operation manuals for FLO 18/60 and FLO 24/80 DCI.
To Next Page
