What to do if AL-KO Robolinho 300 bumper deflected?
If the AL-KO Lawn Mower has driven into an obstacle and cannot free itself, especially near the base station, place the appliance on the designated grass surface. Also, ensure the boundary cable is correctly positioned.
Why does my AL-KO Lawn Mower say no loop signal?
If your AL-KO Lawn Mower displays a 'No loop signal' error, first check the LEDs on the base station. Then, check the power source by disconnecting and reconnecting it. Finally, inspect the boundary cable for any damage and repair it if necessary.
Why is the loop signal weak on my AL-KO Lawn Mower?
If your AL-KO Lawn Mower shows a weak loop signal, check the LEDs on the base station and ensure the power source is properly connected by disconnecting and reconnecting it. If the issue persists, raise the boundary cable to the correct height, attaching it directly to the grass if needed. It might be that the boundary cable is buried too deep.
What to do if AL-KO Lawn Mower is in bad position?
If your AL-KO Lawn Mower is in a bad position, ensure it is placed on the designated grass surface. Correct the boundary cable's location around curves and obstacles, and eliminate any criss-crossing of the cable. This may happen because the appliance is outside the designated grass surface or the boundary cable has been routed in a criss-cross pattern.
How to fix AL-KO Robolinho 300 escaped robot error?
If the AL-KO Lawn Mower has escaped, correct the location of the boundary cable around curves and obstacles, as the appliance is outside the designated grass surface.
What to do if AL-KO Robolinho 300 Lawn Mower shows Cal: no loop CN015: Cal: outside?
If your AL-KO Lawn Mower displays 'Cal: no loop' or 'CN015: Cal: outside' during calibration, check the LEDs on the base station and the power source by disconnecting and reconnecting it. Place the appliance at the prescribed calibrating position, aligned precisely at right angles, ensuring it can drive over the boundary cable. This issue arises because the appliance cannot find the boundary cable during calibration.
Why does my AL-KO Robolinho 300 Lawn Mower show Cal: signal weak?
If your AL-KO Lawn Mower displays 'Cal: signal weak' during calibration, place the appliance at the prescribed calibrating position, aligned precisely at right angles. Also, check the power source of the base station by disconnecting and reconnecting it, and inspect the boundary cable for damage. This can happen because the loop signal is too weak or there is no loop signal, or the boundary cable is faulty.
What to do if AL-KO Lawn Mower shows Cal: Collision?
If your AL-KO Lawn Mower displays 'Cal: Collision' during calibration, remove any obstacles that the appliance has bumped into.
How to fix AL-KO Robolinho 300 Lawn Mower tilt sensor error?
If the AL-KO Lawn Mower's tilt sensor is triggered, place the appliance on a flat surface and acknowledge the fault. This may occur if the maximum tilt is exceeded, the appliance has been carried, or the slope is too steep.
What to do if AL-KO Robolinho 300 lift sensor triggered?
If the lift sensor on your AL-KO Lawn Mower is triggered, remove the obstacle. This can happen if the appliance cover has been deflected upwards by lifting or by an obstacle.
Explains symbols shown on the manual's cover page for quick identification.
Defines warning symbols and text conventions used throughout the manual for safety.
Lists all components included in the standard package for the automatic lawn mower.
Details the components and parts of the Robolinho automatic lawn mower itself.
Explains safety symbols and indicators directly found on the lawn mower unit.
Describes the buttons and display interface on the appliance for user interaction and settings.
Details the information shown on the appliance's display and how to navigate menu items.
Outlines the hierarchical organization of settings and functions accessible via the control panel.
Describes the components and function of the charging and docking station for the mower.
Provides information on the battery, its charging, and maintenance for optimal performance.
Explains how the automatic lawn mower operates on the grass and manages charging cycles.
Details wireless connectivity features and mobile app for remote control and monitoring.
Shows operating hours until next blade service and how to reset the counter.
Displays appliance specifications like type, serial number, operating hours, and cable length.
Displays the current software version of the automatic lawn mower.
Shows current settings like the total weekly mowing time.
Lists fault messages with date, time, and fault code that last occurred.
Instructions for cleaning the automatic lawn mower and base station safely.
Defines the appliance's purpose for non-commercial use and liability exclusion.
Lists inappropriate uses of the machine, such as in public parks or agriculture.
Highlights the importance of functional safety features and warns against disabling them.
Explains the procedure for entering and managing the PIN for appliance startup and security.
Describes the function of various safety sensors like lifting, bump, and tilt sensors.
Provides general safety guidelines for operating the appliance safely.
Specifies age and capability requirements for operating the appliance.
Details necessary clothing and protective gear for safe operation and maintenance.
Advises on ensuring the safety of bystanders and animals during operation.
General safety rules for the machine's condition and proper usage.
Safety precautions related to electrical hazards and water.
Steps to carefully open the packaging and check for transport damage.
Guidance on preparing the lawn and defining the mowing zone for the robot.
Criteria for selecting an optimal and safe spot for the base station.
Instructions on how to lay the boundary wire correctly around the mowing area.
How to create narrow passages to connect separate mowing zones.
Defines the primary mowing zone and how to manage additional areas.
Steps to prepare the lawn, including mowing and removing obstacles.
Instructions for positioning and fixing the base station securely.
Steps for connecting and securing the boundary cable to the base station.
Detailed steps for attaching the boundary wire to the base station terminal.
Guidance on laying the boundary cable on the lawn or under turf.
How to use the boundary cable to avoid specific obstacles on the lawn.
Guidelines for routing boundary cables to create safe passages between mowing areas.
Methods to prevent the mower from entering steep slopes using the boundary cable.
How to create spare loops in the boundary cable for future repositioning or extension.
Common issues encountered with boundary cable installation and their solutions.
Steps to connect the power supply unit to the base station.
How to verify the status indicators and connections of the base station.
Instructions for fully charging the battery before first use.
Guide to configuring language, PIN, date, and time for the appliance.
How to adjust the mower's cutting height for optimal grass length.
Procedure to calibrate the mower's movement within the boundary cable.
Procedures for manual operation, cancelling mowing, and mowing secondary areas.
Accessing general settings, and activating/deactivating button tones and Eco mode.
Configuring the rain sensor, mowing programs, and start points.
Setting mowing times, using inTOUCH app, and manual edge mowing.
Configuring secondary area mowing and adjusting display contrast.
Managing settings lock, recalibrating, and restoring factory defaults.
Weekly checks for the machine, base station, boundary cable, and power supply.
Step-by-step guide to safely replace the mower's cutting blades.
Instructions on how to safely lift and transport the automatic lawn mower.
Guidelines for storing the appliance during off-season or long periods of inactivity.
Instructions for storing the charging pole when the appliance is not in use.
Information on storing the boundary cable during winter months.
Regulations for disposing of electrical appliances and batteries according to German law.
A table listing common malfunctions and their corresponding causes and remedies.
A table detailing specific error codes, their causes, and recommended solutions.
Information on where to seek assistance for warranty, repairs, or spare parts.
Details the conditions under which the warranty is valid and what voids it.
General| Type | Robotic lawn mower |
|---|---|
| Noise level | 60 dB |
| Cutting width | 200 mm |
| Product color | Black, White |
| Rotational speed | 3400 RPM |
| Maximum lawn area | 300 m² |
| Maximum cutting height | 55 mm |
| Minimum cutting height | 25 mm |
| International Protection (IP) code | IPX1 |
| Power source | Battery |
| Battery voltage | 18 V |
| Battery capacity | 2.2 Ah |
| Battery life (max) | 45 min |
Weight and Dimensions| Depth | 400 mm |
|---|---|
| Width | 600 mm |
| Height | 290 mm |
| Weight | 7000 g |
| Package weight | 13000 g |
To Next Page