8AL90323ENAAed01
This manual describes the services offered by the 8262 DECT Handset when connected to an
OmniPCX Office RCE system.
Operating conditions
This approved DECT telephone is intended to be used with an ALE International cordless PABX. The
following conditions must be respected, notably concerning the use of radioelectric frequencies:
Changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
To limit the risk of interference, people with pacemakers must keep the wireless telephone
away from their equipment (minimum distance of 15 cm/6 inches).
It is recommended to follow the standard acceptance procedures before using this equipment in
human safety critical areas (hospitals...).
DECT equipment can only be used to establish links between fixed points if these links are
temporary.
The conditions of access to a DECT equipment telepoint network shall be stipulated by contract
with the operator of the authorized telepoint network concerned.
Switch off the telephone before changing the battery.
You must not switch on or use your telephone near gas or inflammable liquids.
The handset includes magnetic elements that may attract sharp metallic objects.
There is a danger of explosion if the battery is replaced incorrectly. Use only recommended
battery: Alcatel-Lucent 3BN67332AA (Dongguan Deereng New Energy Co. Ltd. RTR001FXX -
Li-ion 3.7V 1100mAh 4.1Wh).
The mains power socket used must be close to the charger/holder and easily accessible, so
that it can be used as an 'on/off' facility.
Battery charge: Charge the battery for about 6 hours before initial use.
The 8262 DECT Handset desktop Dual charger (3BN67346AA), is dedicated for 8262 Dect
handsets (3BN67345AA) and needs the following Power Supply Units:
1. 8232 DECT Handset Desktop charger PSU Europe (3BN67335AA)
TenPao (Model S005AYV0500100) – Class VI (rating I/P:AC 100-240V, 0.2A; O/P: DC 5V,
1A)
Phihong (Model PSA05E-050Q) – Class V (rating I/P:AC 100-240V, 0.2A; O/P: DC 5V, 1A)
Friwo FW7713/XX. (rating I/P:AC 100-240V, 150mA; O/P: DC 5V, 1A)
2. 8232 DECT Handset Desktop charger PSU WW (3BN67336AA)
TenPao (Model S008ACM0500100 with UK,US,AUS plugs) –Class VI (rating I/P:AC 100-
240V, 0.3A; O/P: DC 5V, 1A)
Friwo FW7712 - Class V (rating I/P:AC 100-240V, 125mA; O/P: DC 5V, 0.9A)
You can charge the device by connecting it to a USB 2.0 port (type A). Use only the cable
provided with the 8262 DECT Handset Desktop Dual Charger (USB 'A' plug).
The 8262 DECT Handset Rack Charger (3BN67351AA) will use a dedicated PSU:
1. 8262 Dect handset PSU WW for rack charger (3BN67353AA)
Friwo FW7540/05 (rating I/P:AC 100-240V, 600mA; O/P: DC 5V, 5A)
To prevent possible hearing damage, do not listen at high volume levels for long periods.
The labels and icons presented in this document are not contractually binding and may be modified without
prior warning. The labels and icons displayed on your phone depend on the system to which you are
connected and may differ from those specified in this document.
.
To Next Page
Loading...
