one go. This will harm the lawn. For grass which has grown to over 10 cm in height
we therefore recommend that you mow it with the highest cutting height setting rst.
Important!
The cutting height setting has an inuence on the maximum area that can be mown.
Keep the underside of the lawn mower housing clean and remove grass build-up.
Deposits not only make it more dicult to start the lawn mower; they decrease the
quality of the cut and make it harder for the equipment to bag the grass. Always mow
along inclines (not up and down).
You can prevent the lawn mower from slipping down by holding a position at an angle
upwards. Select the cutting height according to the length of the grass. Make several
passes so that no more than 4cm of grass are cut at one time.
X. Maintenance and cleaning
IMPORTANT: Pull out the safety plug (Fig. 1 / Pos. 5) and remove the batteries (Fig.
1 / Pos. 18) before starting any cleaning work
Cleaning
• Keep all safety devices, air vents and the motor housing free of dirt and dust as
far as possible. Wipe the equipment with a clean cloth or blow it down with com-
pressed air at low pressure.
• Do not clean the lawn mower with running water, particularly with high-pressure
water.
• We recommend cleaning the equipment immediately each time after use.
• Clean the equipment regularly with a damp cloth and some soft soap. Do not use
• cleaning agents or solvents; these may be aggressive to the plastic parts in the
equipment. Ensure that no water can get into the interior of the equipment.
• For best results, clean the lawn mower with a spatula and with a brush or rag.
Maintenance
• Worn out or damaged blades, blade mounts, and bolts should be replaced as a
set by an authorized professional in order to keep the equipment in balance.
• Ensure that all mounting components (i.e. screws, bolts, nuts etc.) are always
tightened so that the equipment can be safely operated at all times.
• Check the grass catch assembly frequently for signs of wear.
• Replace excessively worn or damaged parts immediately.
AUS
FBLM-1000 E1 Maintenance and cleaning
AUS
Operation/Maintenance and cleaning FBLM-1000 E1
• In order to ensure that you enjoy the equipment for many years to come, all
screwed parts, as well as the wheels and axles, should be cleaned and lubricat-
ed.
• Keeping your lawn mower in good condition not only ensures a long lifespan and
high performance, but also enables the equipment to thoroughly cut your grass
with minimal eort.
• The blade is subjected to more wear and tear than any other component. There-
fore, routinely check the condition of the blade and make sure that it is tightly
fastened. If the blade is completely worn out, it must be immediately replaced or
ground sharp again. An excessively vibrating lawn mower means that the blade
is not properly balanced or has become deformed from striking an object. In this
case, the blade must be repaired or replaced.
• There are no other parts inside the equipment which require maintenance.
Replacing the blade
For safety reasons, we recommend having the blade replaced by an authorized pro-
fessional.
Caution! Pull out the Safety plug (Fig. 1 / Pos. 5) and remove the batteries (Fig. 1
/ Pos. 18)! Wear work gloves! Only replace the blade with an original replacement
blade, as this will ensure top performance and safety under all conditions.
Carry out the following steps to change the blade:
1. Undo the fastening screw with the key (Fig. 12 / Pos. 19).
2. Remove the blade and replace with a new one.
3. When tting the blade, make sure it is installed in the correct direction.
4. Retighten the fastening screw. The tightening torque should be approx. 25 Nm.
At the end of the season, perform a general inspection of the lawn mower and
remove any grass and dirt which may have accumulated. At the start of each
season, ensure that you check the condition of the blade. If repairs are neces-
sary, please contact our customer service center. Use only genuine spare parts.
AFTER SALES SUPPORT
27
1300 855 831
support@scheppach.com.au
MODEL: FBLM-1000 E1 PRODUCT CODE: 706547 09/2021
26
AFTER SALES SUPPORT
support@scheppach.com.au
1300 855 831
MODEL: FBLM-1000 E1 PRODUCT CODE: 706547 09/2021
To Next Page
Loading...
