Alinco DR-150 T - Table of Contents

65 pages

Save Page as PDF

To Next Page

To Previous Page

Main Page

Table of Contents2
Notice4
Before Operating the Transceiver5
Standard and Optional Accessories5
Mobile Antenna Installation6
Location6
Power Requirements6
Base Station Installation6
Specifications7
Panel Description8
Front Panel8
Primary Functions8
Secondary Functions after F Is Pushed for Less than 0.5 Sec (Func Appears)9
Functions after Pushing the F Key for more than 0.5 Sec (Func Appears and Flashes)9
Functions Pressed While Turning Power on9
Display10
Rear Panel11
Microphone11
Microphone Pin Assignments11
Basic Operation12
Receiving12
Adjusting the Audio Volume12
Adjusting the Squelch12
Receive Frequency Range (Mhz)13
Selecting a Frequency13
Changing the Mhz Digit Only13
Transmitting14
Transmit Frequency Range (Mhz)14
Selecting a Frequency for Transmit14
Selecting an Output Power14
Operating Modes15
VFO Mode15
Memory Mode15
Call Mode15
Main and Sub Band Operation16
Changing Bands16
Advanced Functions17
Memory Channels17
Memory Types and Default Settings from the Factory17
Calling up a Memory Channel17
Temporarily Changing a Memory Channel Frequency (Temporary Mode)18
Programming a Memory Channel18
Clearing a Memory/Reclaiming a Memory19
Transferring a Memory to VFO20
Operating in Memory Channel Indication Mode (Channelized Mode)20
Call Channel21
Calling up the Call Channel (Call Mode)21
Changing the Call Channel's Frequency21
Channel Scope22
VFO Channel Scope22
What Do the VFO Scope Level Indications Mean?23
Changing the Center Frequency23
Memory Channel Scope24
What Do the Memory Scope Level Indications Mean?24
Changing the Center Channel24
Channel Scope Operation with the DTMF Equipped Microphone (EMS-12)25
Starting and Stopping the Scope Function25
Changing the Center Channel Receive Period (5 Sec./O Sec.)25
Receiving in Single Start Mode25
Scanning26
Setting a Scan Type26
Band Scan27
Programmed Scan27
Programming the Scan Range into Memory27
Programmed Scan from VFO Mode28
Programmed Scan from Memory Mode28
Memory Scan29
Setting Non-Scan (Skip) Channels29
Operation During Scanning29
Band Sweep Scan30
What Do the Sweep Scan Levels Mean?30
Programmed Sweep Scan30
Memory Sweep Scan31
Priority Watch on 2 Channels32
Other Functions33
S-Meter Squelch Function33
Setting a Squelch Level During Normal Receive33
Setting a Squelch Level During the Channel Scope Operation33
Setting the Squelch Timer34
Shift and Split Settings (Using Different Frequencies for Transmit and Receive)35
Reverse (Transmit and Receive Frequencies Are Exchanged)36
Setting the Tone Encoder37
Changing Tuning Steps38
Key Lock Function38
Bell Function On/Off39
Adjusting the Display Brightness39
Beep Tones On/Off40
Setting the Transmit Time-Out Timer40
RF Attenuator On/Off41
Sending a Tone Burst Signal41
Changing the Call/Tone Key Function41
Receive LITZ Signal42
AM Receive42
Cloning43
Receiving Side (Slave) Error43
Resetting the CPU44
Full Reset (All Settings Are Returned to Their Initial Values)44
VFO Reset (VFO a and B Settings Only Are Returned to Their Initial Values)44
Factory Default Conditions44
Selective Calling45
Tone Squelch (CTCSS)45
DTMF Squelch (DSQ)45
There Are Three DSQ Modes45
Setting a Tone Squelch Frequency46
Tone Scan47
Setting DSQ Mode48
Programming DSQ Codes49
Off (Monitor Off)49
Setting DSQ Mode with a DTMF Microphone (EMS-12)50
Programming DSQ Codes Using DTMF Microphone (EMS-12)50
Communicating in Code Squelch Mode (DSQ)51
Notes for DSQ Operation51
Communicating in Group Pager Mode (G DSQ)52
Preparation52
Communicating in Private Pager Mode (P DSQ)53
Changing the Rate of Transmission of DTMF Codes54
Adjusting the DTMF Code Burst Time54
Transmitting DTMF Codes Manually54
Auto-Dialing55
Programming Transmit Codes into Memory55
Programming a Pause55
Correcting a Code that You Have Entered56
Clearing a Code56
Confirming a Received DTMF Code56
Transmitting a Specific Memory57
Transmitting Dial Memory M157
Inhibiting Auto-Dialing (Clearing Dial)57
Microphone Remote Control Commands58
Operating Procedure for Microphone Remote Control58
Explanation of Commands59
Entering a Frequency Directly60
DTMF Microphone (EMS-12)60
Packet Operation61
Requirements for Packet Operation61
TXD (Transmit Data) Input Sensitivity61
1200 Bps Packet Operation62
Connecting Equipment for Packet Operation62
9600 Bps Packet Operation63
Connections for Packet Operation63
Maintenance64
Troubleshooting64

Alinco DR-150 T - Table of Contents

Table of Contents

Related product manuals