Need help?Do you have a question about the ALLEN & HEATH XB-14 and is the answer not in the manual?
Operating Levels| Mono channel Mic input range | +6 to –63dBu |
|---|---|
| Mono channel Line input range | +10 to –26dBu |
| Insert point nominal level | 0dBu |
| Stereo input nominal level | 0dBu |
| Telco channel input range | +10 to –26dBu |
| External monitor inputs nominal level | 0dBu |
Output Levels| PGM L & R outputs nominal level | +4dBu |
|---|---|
| PGM Mono output nominal level | 0dBu |
| PGM L & R inserts nominal level | -2dBu |
| Aux output nominal level | 0dBu |
| Mix B outputs nominal level | 0dBu |
| Rec outputs nominal level | 0dBu |
Audio Performance| THD+n Mic in to PGM L/R Out | 0.003% |
|---|---|
| THD+n Mic in to PGM Out | 0.007% |
| THD+n Line in to PGM L/R out | 0.004% |
| THD+n Stereo in to PGM out | 0.003% |
| Noise Mic Pre EIN | -127dBu |
| Noise PGM out | -92dBu |
Frequency Response| Mic in to PGM L/R Out | 20Hz to 20kHz |
|---|---|
| Line in to PGM L/R out | 10Hz to 30kHz |
| Stereo in to PGM L/R out | 10Hz to 30kHz |
Headroom| Analogue Headroom Outputs | 21dB |
|---|---|
| USB in & out headroom | 14dB |
| Analogue Headroom Mix point | 24dB |
Crosstalk & Attenuation| Mono fader attenuation 1kHz/10kHz | -99/-90 |
|---|---|
| Mono ON switch attenuation 1kHz/10kHz | -96/-80 |
| TELCO fader attenuation 1kHz/10kHz | -99/-92 |
| TELCO ON switch attenuation 1kHz/10kHz | -102/-100 |
| Stereo fader attenuation 1kHz/10kHz | -100/-91 |
| Stereo ON switch attenuation 1kHz/10kHz | -102/-102 |
Details the conditions required for the one-year warranty to be valid.
Guides on how to properly wire and replace the mains plug for safety and compliance.
Outlines general care and handling guidelines to prevent damage and ensure safe operation.
Discusses multi-application, pre-amps, EQ, AUX, MIX B, Remote Control, USB, and operational modes.
Details the nominal and maximum operating levels for all input and output connectors.
Provides Total Harmonic Distortion plus noise measurements for various signal paths.
Specifies the USB audio interface capabilities, including sample rate and bit depth.
Details headroom for outputs and crosstalk/attenuation figures between channels.
Outlines the frequency response for various input signals to the main outputs.
Explains the XLR Mic input, 1/4" Line input, Insert socket, and Gain adjustment.
Describes the function of the 100Hz high-pass filter for reducing low-frequency noise.
Explains the High Frequency (12kHz) and Mid Frequency (sweepable) EQ controls.
Describes the Low Frequency (80Hz) EQ control and its response graph.
Details the auxiliary send, stereo Mix B routing, and stereo pan controls.
Explains the channel ON/Mute switch, signal/peak indicators, PFL function, and the 100mm fader.
Describes the Telco input (XLR) and Clean-Feed output (XLR) connectors.
Explains the Telco input gain, 100Hz high-pass filter, and 2-band EQ.
Details the Talk function for communication and the CLF Source switch for caller audio.
Describes the auxiliary send, Mix B routing, and pan controls for Telco channels.
Explains the ON switch, signal/peak LEDs, PFL, and the channel fader operation.
Describes the 1/4" ST1 and RCA ST2 inputs and the source selector switch.
Covers stereo input level adjustment, 2-band EQ, and the auxiliary send control.
Explains balance, the ON switch with start/cue logic, and signal/peak LEDs.
Details the PFL function and the 100mm fader for stereo channels.
Describes configurations for the stereo channel ON switches, including disabling mute or jamming ON.
Covers the REC OUT connector and the USB RTN (ST6) level control.
Explains CRM speaker outputs and the USB audio send/return functionality.
Covers MIX B OUT, External Monitor Input, Main PGM Inserts, and Main PGM Outputs.
Details AUX Output, Mono Output, and Headphone output sockets for operator and guests.
Explains the 48V Phantom Power switch and the Left/Right LED meters.
Details CRM/Guest headphone source selectors and CRM speaker level adjustment.
Details CRM speaker level, DIM/Cut, MIC FADER UP, and Control Room/Guest phone levels.
Explains the Mix B level control and the main Program Mix fader.
Provides pin configurations and functions for REMOTE A and REMOTE B connectors.
Explains the logic signals for controlling external equipment like CD decks.
Explains the USB audio interface capabilities and driver compatibility.
Instructions on adjusting volume levels for the USB audio device in Windows.
Explains how to wire insert cables for send and return signals.
Covers wiring for MIC, TRS, and XLR cables for balanced and unbalanced connections.
Instructions on how to register the product online or by mail for warranty and support.
To Next Page
