Alliance Laundry Systems 805413R1

Questions and Answers

P
Paul HamiltonAug 16, 2025
Why won't my Alliance Laundry Systems 805413R1 start?
- M
  martindeborahAug 16, 2025
  If your Alliance Laundry Systems Washer won't start, there are several things you can check: Ensure the power cord is fully plugged into the electrical outlet. Check the laundry room's fuse or circuit breaker. Verify that the controls are correctly set and press the START keypad. Also, make sure the loading door is closed tightly, coin(s) or card are inserted, and the door latch is properly adjusted relative to the door lock.
S
Samantha SchneiderAug 19, 2025
What to do if my Alliance Laundry Systems Washer won’t fill?
- A
  Angela HoffmanSep 12, 2025
  If your Alliance Laundry Systems Washer isn’t filling, try these solutions: Ensure the power cord is fully plugged into the outlet, and check the laundry room's fuse or circuit breaker. Verify the controls are properly set and that you've pressed the START keypad. Confirm the loading door is tightly closed and both hot and cold water faucets are turned on. Also, check that the fill hoses aren’t kinked or twisted, and clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses.
J
Joshua MasonAug 22, 2025
What to do if my Alliance Laundry Systems 805413R1 won't drain?
- S
  sharon33Aug 22, 2025
  If your Alliance Laundry Systems Washer isn't draining, make sure the drain hose isn't kinked, twisted, or clogged. Also, check that the drain receptacle isn't clogged. If there is a foreign object trap in the pump, clean it.
C
cmillerAug 25, 2025
How to fix water leaks in my Alliance Laundry Systems Washer?
- W
  whitethomasAug 26, 2025
  To address water leaks in your Alliance Laundry Systems Washer, first, check that the fill hoses are properly installed on both the faucets and the washer's water mixing valve. Inspect the fill hoses for wear and consider replacing them every five years. Ensure the drain receptacle isn't clogged and check your laundry room plumbing. Examine the rubber door gasket for any tears or holes. If there's excessive sudsing, ensure you're using a low-sudsing, high-efficiency (HE) detergent and using proper load sizes. Finally, ensure the outside perimeter of the door glass where the seal contacts the glass is clean.
L
Linda LawrenceAug 28, 2025
Why is my Alliance Laundry Systems Washer vibrating so much?
- K
  Kelly HoodAug 28, 2025
  Excessive vibration in your Alliance Laundry Systems Washer could be due to a few reasons. Ensure the washer is level, as uneven leveling can cause vibration. Also, make sure the washer is installed on a solid, sturdy, and level floor, avoiding carpeting, soft tile, platforms, or weakly supported structures. Finally, ensure rubber feet are installed on all four leveling legs.
B
Brittany HensonAug 31, 2025
What to do if my Alliance Laundry Systems 805413R1 Washer load is too wet?
- C
  Cameron SchroederAug 31, 2025
  If your laundry load is too wet after a cycle in your Alliance Laundry Systems Washer, it might be due to an unbalanced load, which causes the washer to limit the spin speed. Try redistributing the load. Alternatively, if the load is too small, add more items to make it a full load.
N
Norman JacksonSep 3, 2025
Why won't my Alliance Laundry Systems Washer spin or tumble?
- J
  Jared HenrySep 3, 2025
  If your Alliance Laundry Systems Washer won’t spin or tumble, make sure the power cord is plugged in all the way, and check the laundry room fuse or circuit breaker. Ensure the controls are properly set, and press the START keypad. Also, check that the loading door is closed tightly. If the drive belt is broken, call a service person. If a foreign object trap in the pump is clogged, clean the trap.
A
Anthony JonesSep 6, 2025
Why does my Alliance Laundry Systems 805413R1 have too many soap suds?
- K
  Kelly GallagherSep 6, 2025
  Too many soap suds in your Alliance Laundry Systems Washer may be because the laundry load is oversudsing. Make sure you are using low-sudsing, high-efficiency (HE) detergent and the amount of detergent recommended on the detergent’s label. If using non-HE detergent, use only 1/2 of the detergent manufacturer's recommended amount. Also, ensure you are using proper load sizes.
A
ariana45Sep 9, 2025
Why does my Alliance Laundry Systems Washer stop during the cycle?
- Z
  zmarquezSep 9, 2025
  Pauses during a cycle are part of the normal operation of the Alliance Laundry Systems Washer. However, you should also check the laundry room fuse or circuit breaker. An unbalanced wash load may also cause the washer to stop and then restart the spin automatically.
S
Steven WilsonSep 12, 2025
Why is my Alliance Laundry Systems 805413R1 Washer using the wrong water temperature?
- E
  Edward BrownSep 12, 2025
  If your Alliance Laundry Systems Washer is using the wrong water temperature, first, ensure that the controls are properly set. Check the fill hoses to confirm that the hot faucet hose is connected to the hot mixing valve (indicated with “H” on the valve bracket) and the cold faucet is connected to the cold mixing valve (indicated with “C” on the valve bracket). Finally, ensure your laundry room water heater is adjusted properly.