20-EN
4
Turn the Rotary encoder to adjust the level, and then
press ENTER.
LEVEL: 0 ~ 8
5
Repeat steps 3 to 4 to complete the setting of other bands.
Note
• There is no MX mode for FM, MW and LW radio.
You can change the unit of time correction (centimetres or inches).
Setting item: LENGTH
Setting contents:
CM (Initial setting) / INCH
CM:
Time correction value is in centimetres.
INCH:
Time correction value is in inches.
Before performing the following, refer to “About Time Correction” on
page 21.
1
Turn the Rotary encoder to select the desired speaker
after selecting TCR, and then press ENTER.
FRONT-L FRONT-R REAR-L REAR-R SUBW-L
SUBW-R FRONT-L
2
Turn the Rotary encoder to adjust the distance of the
selected speaker, and then press ENTER.
0.0 cm to 336.6 cm (3.4 cm/step)
0.0 inch to 132.7 inch (1.3 inch/step)
Note
• The total adjustment distance for all speakers should be less than 510
centimetres (201 inches).
3
Repeat steps 1 and 2 for setting other speakers.
By setting these values, sound from all speakers can be made to
reach the listener at the same time.
This function allows you to change the sound field easily.
There are three modes to choose from. For details, refer to the table
below.
Before performing the following procedures, refer to “About the
Crossover” on page 22.
Setting item: X-OVER
1
Turn the Rotary encoder to select the channel, and then
press ENTER.
FRONT (HPF) REAR (HPF) SUBW LPF FRONT (HPF)
2
Turn the Rotary encoder to select the desired item, and
then press ENTER.
Selecting the Cut-Off Frequency (FREQUENCY)
Setting contents:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 /
160 / 200 (Hz)
Adjusting the Slope
Setting contents:
FLAT (Initial setting) / 6 / 12 / 18 / 24 (dB/oct.)
Adjusting the Level
Setting contents:
−12 to 0 (dB) (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
Note
• While adjusting the X-OVER, you should consider the frequency
response of the connected speakers.
The Settings of 9BAND P-EQ/TCR/X-OVER can be stored in the preset
memory.
1
The 9BAND P-EQ/TCR/X-OVER settings can be stored in
any one of the preset buttons (1 through 6). After
completing any adjustment for 9BAND P-EQ/TCR/X-OVER
(e.g. BAND), press and hold the desired preset button for
at least 2 seconds.
2
Turn the Rotary encoder to select PROTECT NO/YES, and
then press ENTER to store the adjusted contents.
PROTECT NO PROTECT YES (Initial setting)
Notes
• If YES is selected, the adjusted contents are protected and stored into the
preset buttons. When you want to store the parameter into a protected
preset button, “REPLACE NO/YES” can be selected.
If NO is selected, the preset is stored.
• While performing this operation, all adjusted contents of Parametric
EQ/Time Correction/X-Over will be stored in the preset buttons.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation (refer to
“Recalling the Stored 9BAND P-EQ/TCR/X-OVER Adjustment
Settings” on page 21).
Setting the Time Correction Unit
(LENGTH)
Adjusting the Time Correction (TCR)
Adjusting the SPATIAL
Mode Effect
OFF
(Initial setting)
No effect is applied.
OFF status
FRONT WIDE
Creates the effect of widening the front sound
field by delaying the sound of the front
speakers.
REAR WIDE
Creates the effect of making the front sound
image clear and far by delaying the sound of
the rear speakers.
Adjusting the Crossover Settings
(X-OVER)
Storing the 9BAND P-EQ/TCR/X-OVER
Settings
To Next Page
Loading...
