Table of Contents
6
D9 BAH0007.3 08.10
5.3
Adjusting the sowing rate...................................................................................................... 54
5.3.1 Seed wheel drive................................................................................................................... 55
5.3.2 Seed dosing .......................................................................................................................... 55
5.3.3 Setting values table............................................................................................................... 56
5.3.4 Seed wheel (normal and fine seed wheel)............................................................................ 57
5.3.5 Bean seed wheel (option) ..................................................................................................... 57
5.3.6 Base flaps.............................................................................................................................. 57
5.3.7 Agitator shaft ......................................................................................................................... 58
5.3.8 Sowing peas.......................................................................................................................... 59
5.3.9 Sowing beans........................................................................................................................ 60
5.3.10 Calibration cups..................................................................................................................... 61
5.3.11 Ready reckoner disc .............................................................................................................61
5.4 Operator terminal (option) ......................................................................... 62
5.5 Operator terminal (option)...................................................................... 62
5.6 WS coulter............................................................................................................................. 63
5.6.1 Band sowing shoe (option).................................................................................................... 63
5.7 RoTeC coulter ....................................................................................................................... 64
5.8 Coulter pressure.................................................................................................................... 65
5.9 Harroweeder (option) ............................................................................................................67
5.10 Drag tine harrow (option) ...................................................................................................... 68
5.11 Seed drill wheel mark eradicator (option) ............................................................................. 69
5.12 Tractor drill wheel mark eradicator (option) .......................................................................... 69
5.13 Markers ................................................................................................................................. 70
5.14 Hectare counter AMACO (optional)................................................................................. 71
5.15 Tramline selection (option).................................................................................................... 72
5.15.1 Examples for creating tramlines............................................................................................ 74
5.15.2 Tramline rhythm 4, 6 and 8 ................................................................................................... 76
5.15.3 Tramline rhythms 2 plus and 6 plus ...................................................................................... 77
5.15.4 Tramline control..................................................................................................................... 77
5.15.5 Switching off the seed shaft on one half ............................................................................... 79
5.15.6 Tramline marker (option)....................................................................................................... 79
6 Commissioning ......................................................................................... 80
6.1 Checking the suitability of the tractor.................................................................................... 81
6.1.1 Calculating the actual values for the total tractor weight, tractor axle loads and load
capacities, as well as the minimum ballast ........................................................................... 81
6.1.1.1 Data required for the calculation (attached machine) ........................................................... 82
6.1.1.2 Calculation of the required minimum ballasting at the front G
V min
of the tractor to
ensure steering capability ..................................................................................................... 83
6.1.1.3 Calculation of the actual front axle load of the tractor T
V tat
................................................... 83
6.1.1.4 Calculation of the actual total weight of the combined tractor and machine......................... 83
6.1.1.5 Calculation of the actual rear axle load of the tractor T
H tat
................................................... 83
6.1.1.6 Tractor tyre loadbearing capacity.......................................................................................... 83
6.1.1.7 Table ..................................................................................................................................... 84
6.2 Securing the tractor / machine against unintentional start-up and rolling............................. 85
6.3 Initial fitting of the operating terminal .................................................................................... 85
6.4 Initial fitting of the harroweeder (specialist workshop) .......................................................... 86
6.5 Initial fitting of the loading board (specialist workshop)......................................................... 86
6.6 Initial installation of mounts for the road safety bar............................................................... 87
7 Coupling and uncoupling the machine ................................................... 88
7.1 Coupling the machine ........................................................................................................... 88
7.1.1 Connecting the hydraulic connections .................................................................................. 92
7.1.2 Make the further connections................................................................................................ 93
7.2 Uncoupling the machine........................................................................................................ 94
To Next Page