Ametek Sorensen XG 6-220 User Manual

PROGRAMMABLE POWER
M370430-01 Rev F www.programmablepower.com
XG Family Programmable DC
Power Supply
Operating Manual
(firmware v 2.0 and higher)
670 Watts – 1700 Watts
Half Rack
Full Rack
6 V to 600 V Models:
6-110
6-220
6-220
8-100
8-187.5
8-200
12-70
12.5-120
12-140
20-42
20-76
20-84
33-25
30-50
33-50
40-21
40-38
40-42
60-14
60-25
60-28
80-10.5
80-19
80-21
100-8.5
100-15
100-17
150-5.6
150-10
150-11.2
300-2.8
300-5
300-5.6
600-1.4
600-2.6
600-2.8

Ametek Sorensen XG 6-220 Specifications

General

Power Rating	1320 W
Output Type	DC
Operating Temperature	0 to 50 °C
Input Frequency	47-63 Hz
Cooling	Forced air
Control Interface	RS-232
Ripple and Noise	10 mV RMS
Output Voltage Range	0-6 V
Output Current Range	0-220 A

Summary

Installation

Basic Setup Procedure

Summary of the essential steps for installing the power supply.

Step 3: Connecting AC Input Power

Instructions for safely connecting the AC input power to the unit.

Step 4: Selecting Load Wires

Recommendations for choosing appropriate wire sizes for load connections.

Step 5: Performing Functional Tests

Procedures for verifying power supply operation and front panel controls.

Step 6: Connecting Loads

Instructions on how to connect loads to the DC output terminals.

Step 7: Connecting Remote Sensing

Procedure for connecting remote sensing wires to ensure accurate regulation.

Local Operation

Configuring Settings from the Front Panel

Guidance on adjusting settings using the front panel controls.

Alarms and Errors

Information on conditions that cause alarms and error messages.

Using Over Voltage Protection (OVP)

How to configure and use the Over Voltage Protection feature.

Using Under Voltage Protection (UVP)

How to configure and use the Under Voltage Protection feature.

Over Current Protection (OCP)

Details on the Over Current Protection alarm and its configuration.

Resetting the Power Supply

Procedure for performing a soft reset to factory default settings.

Analog Programming (APG) and Isolated Analog Programming (ISOL)

Analog Programming (APG) of Output Voltage and Output Current

How to control output voltage and current using analog sources.

Voltage-Controlled Voltage APG Setup

Procedure for setting up voltage control using an external voltage source.

Voltage-Controlled Current APG Setup

Procedure for setting up current control using an external voltage source.

Resistive-Controlled Voltage APG Setup

Procedure for setting up voltage control using an external resistor.

Resistive-Controlled Current APG Setup

Procedure for setting up current control using an external resistor.

Isolated Analog Programming Mode (ISOL)

Overview of the Isolated Analog Programming mode.

Voltage-Controlled Voltage ISOL Setup

Procedure for voltage control using an isolated external voltage source.

Voltage-Controlled Current ISOL Setup

Procedure for current control using an isolated external voltage source.

Resistive-Controlled Voltage ISOL Setup

Procedure for voltage control using an isolated external resistor.

Resistive-Controlled Current ISOL Setup

Procedure for current control using an isolated external resistor.

Remote Operation

Hardware and Connection Setup

Information on setting up hardware for remote interfaces.

Configuring Remote Control Using RS-232

Steps to configure remote control using the RS-232 interface.

Configuring Remote Control Using RS-485

Steps to configure remote control using the RS-485 interface.

Configuring Remote Control using the USB Connector

Status Reporting in SCPI

Operation Status Register

QUEStionable Status Register

SCPI Error/Event Queue

Reset Command

Auto Sequence Programming

Communications Options

SETTING UP LAN/ETHERNET

Communication Configuration

CONNECTING TO A NETWORK

AMETEK LXI DISCOVERY BROWSER

AMETEK ENETTEST UTILITY

SETTING LAN PARAMETERS

Calibration and Troubleshooting

Main Voltage and Current Calibration Principle

Calibrating the Output Voltage

Calibrating the Output Current

Over Voltage Protection Calibration

Non-isolated Analog Programming Calibration

Isolated Analog Programming Calibration

Calibrating the Input Voltage APG Signal

Calibrating the Input Current APG Signal

Emergency Shutdown

APPENDIX A SCPI Command Reference

SCPI Command Hierarchy

Using SCPI Commands

SCPI Command Summary

A table summarizing supported SCPI commands.

APPENDIX B Error Messages

Error Messages

Command Error List

List of IEEE 488.2 syntax errors detected by the instrument's parser.

Execution Error List

List of errors detected by the instrument's execution control block.

Device-Specific Error List

List of errors detected by instrument operations not covered by other classes.

Query Error List

List of errors related to output queue control and message exchange protocol.

APPENDIX C Specifications

Electrical Specifications for XG Family, 850 W

Detailed electrical specifications for the XG 850 Watt models.

Electrical Specifications for XG Family, 1500 W

Detailed electrical specifications for the XG 1500 Watt models.

Electrical Specifications for XG Family, 1700 W

Detailed electrical specifications for the XG 1700 Watt models.

Common Specifications for All Models

APPENDIX D Rack Mount Options and Installation Instructions

Rack Mount Kit Options

Mounting Option A: 1U Rails

Installation Procedures

Mounting Option B: Manufactured Slides from Jonathan® Engineered Solutions

APPENDIX E Lantronix Procedures for MEA Option

Setting Up the Computer

Software Installations

Configuring the Device Using DeviceInstaller

Assigning an IP Address to the Power Supply Unit

Setting Up Your System

Troubleshooting for XG 850W Model with ENET and/or RS-485 Communication

Troubleshooting common issues with ENET/RS-485 communication.

Troubleshooting for ENET Communication

Specific troubleshooting steps for ENET communication issues.