Anderson RB 680 - User Manual

Questions and Answers

Y
ywarrenAug 3, 2025
Why is the turntable on my Anderson RB 680 not turning or turning slowly?
- K
  knighthaleyAug 3, 2025
  If the turntable on your Anderson Farm Equipment isn't turning or is moving slowly: * The hydraulic oil level might be too low due to leaks or insufficient oil. Inspect for any oil leaks and fix them as necessary. Then, add hydraulic oil to the tank. * Voltage drop. Ensure you have 12 V by recharging or replacing the battery. * The HONDA engine might not be running at the correct speed. Adjust the engine to 3600 revolutions per minute.
J
John SantiagoAug 7, 2025
Why is the plastic film wrapping unsatisfactory on my Anderson RB 680 Farm Equipment?
- T
  tevansAug 7, 2025
  If the plastic film wrapping on your Anderson Farm Equipment is unsatisfactory, consider these issues: * The plastic film may break, develop holes, or tear during wrapping. Check the roll for pre-existing damage and replace it if needed. * Obstructions in the film stretcher. Remove any hay or other objects blocking the plastic film stretcher, and ensure all rollers turn freely. * The film may be too soft due to sun exposure. Install a cooler roll. * The plastic film may not be tight enough on the bale. Check if the plastic film roll is properly installed. * The components of the plastic film stretcher may be in poor condition. Repair as needed.
A
Austin WrightAug 11, 2025
Why doesn't the plastic film cutter work well on my Anderson RB 680 Farm Equipment?
- W
  walterkellyAug 11, 2025
  If the plastic film cutter on your Anderson Farm Equipment isn't working well, it might be because the plastic film cutter clamp isn't holding onto the end of the plastic film. This can happen if the rubber stopper moves back too far on its adjustment bolt. Adjust the bolt to correct this. Also, make sure the stopper spring has enough tension.
D
David VillaAug 15, 2025
What to do if the TAC-08C receiver on my Anderson Farm Equipment is not working?
- K
  kenneth89Aug 16, 2025
  If the TAC-08C receiver on your Anderson Farm Equipment isn't working, consider these potential causes: * A defective power supply. Check the battery contacts and electrical connectors, and clean them if necessary. * Insufficient voltage. Ensure a minimum of 12 V is available by checking the battery and alternator performance, correcting if necessary. * Blown fuse(s) in the receiver case. Replace any defective fuses in the computer case. * Blown power cable fuse. Replace the defective fuse.
E
emily61Aug 20, 2025
Why can't I perform table alignment on my Anderson RB 680?
- T
  Timothy SanchezAug 20, 2025
  If you're unable to perform table alignment on your Anderson Farm Equipment: * The battery may be too weak. Ensure you have 12 V by recharging or replacing the battery. * There may be defective electrical connections. Check the electrical connections, specifically the connectors on the hydraulic valves.
D
David ReynoldsAug 25, 2025
What to do if the TAC-08 remote control does not work on my Anderson RB 680 Farm Equipment?
- C
  Christopher HughesAug 25, 2025
  If the TAC-08 remote control for your Anderson Farm Equipment isn't working or appears unassociated: * The transmitter battery might be dead. Install the charger or use the DC wire connected. * The remote control may not be associated. See remote control association section.
A
Amy BakerAug 28, 2025
What to do if the tilting table remains stuck on my Anderson RB 680?
- W
  williamspaulAug 28, 2025
  If the tilting table on your Anderson Farm Equipment remains in a raised or lowered position and the hydraulic engine continues to strain, the table sensor in raised or lowered position may not be working correctly. Readjust the sensor.