Anderson WRAPTOR - User Manual

Questions and Answers

J
Jennifer BlackAug 14, 2025
Why won't my Anderson WRAPTOR Farm Equipment engine start?
- D
  Douglas HaleyAug 15, 2025
  If the engine of your Anderson Farm Equipment doesn't start, several factors could be at play. First, make sure the fuel valve is open. Next, verify that the gas tank isn't empty and, if it is, add fuel. For Honda engines, a low oil sensor might be the culprit, so check and add oil if necessary. Inspect the spark plug for clogs or defects, cleaning or replacing it as needed. If the engine was flooded during transportation because the fuel valve wasn't closed, remove and dry the spark plug, dry the cylinder using the starter crank, then reinstall the spark plug and try starting again. Finally, check that there isn't too much oil in the oil pan and adjust the oil level if needed.
A
Anthony VasquezAug 18, 2025
What to do if the remote control for my Anderson WRAPTOR Farm Equipment stops working?
- U
  ufordAug 18, 2025
  If the remote control for your Anderson Farm Equipment isn't working or has stopped, the issue might be the 12V battery. Try changing the battery or checking its connection. After that, try pressing the right and left direction buttons in alternation to reprogram the remote operation. Also, ensure that you are not too far from the module; moving closer might resolve the problem.
A
Allison WolfeAug 21, 2025
Why does the hoop on my Anderson WRAPTOR Farm Equipment lose speed?
- J
  josephacostaAug 21, 2025
  If the hoop on your Anderson Farm Equipment loses speed, the issue could be a lack of hydraulic oil or pressure. Check the oil level and inspect for any leaks. Adjust as needed to ensure proper oil levels and pressure.
K
kathryn41Aug 25, 2025
What to do if the hoop on my Anderson WRAPTOR Farm Equipment does not turn?
- D
  davisdouglasAug 25, 2025
  If the hoop on your Anderson Farm Equipment isn't turning, start by checking if the drive wheel is sliding on the hoop. If so, tighten the wheel spring. Also, verify and adjust the tire air pressure as needed. If the tire is worn out, replace it. Also, check the oil level and look for leaks. Finally, inspect the condition of the wheel motor and replace it if necessary.
S
Samantha DiazAug 28, 2025
Why does the plastic film break on my Anderson Farm Equipment at normal temperatures?
- K
  Kelly MaddenAug 28, 2025
  If the plastic film on your Anderson Farm Equipment breaks at normal temperatures, several factors could be the cause. First, ensure the plastic film roll is installed correctly as shown in the diagram. Check that the stretcher and spring parts are in good condition. Also, remove any debris wrapped around the rolls or in the stretchers, and inspect the general condition of the stretchers. Clean dirty aluminum rollers with penetrating oil. Replace a damaged rubber roller. Gently sand any rough spikes.
J
jared30Aug 31, 2025
Why does the plastic film on my Anderson WRAPTOR Farm Equipment break in hot weather?
- K
  Kenneth HobbsAug 31, 2025
  If the plastic film on your Anderson Farm Equipment often breaks in hot weather, it might be because the stretcher springs are putting too much pressure on the hoop. Try unhooking the stretcher springs to alleviate this pressure.
D
Diane DiazSep 3, 2025
Why does the emergency stop activate itself on my Anderson Farm Equipment?
- C
  Christopher HolmesSep 3, 2025
  If the emergency stop activates itself on your Anderson Farm Equipment, it might be due to greasy residues on the piston causing vibrations of the plastic detector. To fix this, take apart the emergency stop valve and clean the piston with a solvent, then reinstall the valve.
T
teresa85Sep 7, 2025
What to do if the remote control for my Anderson WRAPTOR doesn't start after pressing the stop button?
- H
  Holly HurstSep 7, 2025
  If the remote control for your Anderson Farm Equipment doesn't restart after pressing the stop button, the remote operation emergency stop might still be activated. Deactivate it by pressing the left arrow, then the right arrow. After that, restart the bale wrapper by pressing the ON button.
M
Mary MooreSep 10, 2025
How to fix an Anderson WRAPTOR engine that starts but won't stop?
- R
  ryanfloresSep 12, 2025
  If the engine of your Anderson Farm Equipment starts with the key but doesn't stop, and the engine kill switch isn't working, the switch might be defective. Disconnect the orange and black wires, then reconnect the black wire in place of the orange wire. Restart the engine and try stopping it with the key.

Summary

Anderson Limited Warranty

One-Year Limited Warranty Details

Covers defects in materials, manufacturing, or assembly for one year.

Problem Resolution Steps

Outlines procedures for addressing issues, involving dealer and manufacturer contact.

Warranty Exclusions and Limitations

Lists parts and conditions not covered by the warranty, and exclusive remedies.

Safety Precautions

Operator Safety and Training

Emphasizes operator competence, awareness of danger zones, and safe practices.

Operational Safety Guidelines

Advises on safe attire, hearing protection, fuel handling, and hydraulic oil safety.

End of Day and Maintenance Safety

Procedures for safe shutdown, securing the machine, and notices before maintenance.

General Machine Information

Design and Specifications Overview

Details the machine's design, engine, wrapping capacity, dimensions, and weight.

Manual Guidance

Recommends thorough review of the manual for proper operation and maintenance.

Moving and Transporting the Wrapper

Moving Procedures

Instructions for moving the bale wrapper over various distances, including road travel.

Transport Safety Measures

Safety precautions during transportation, securing the load, and using work lights.

Fodder Silage Production

Benefits of Silage and Round Bales

Explains fodder silage benefits, advantages of round bales, and continuous wrapping cost savings.

Optimal Harvest and Baling Times

Guidance on selecting the best time to harvest crops and bale fodder for quality silage.

Wrapping Operations Setup

Plastic Film Roll Installation

Step-by-step guide for loading and installing plastic film rolls onto the wrapping hoop.

Hoop and Stretcher Adjustments

Instructions for adjusting the hoop drive wheel, plastic film stretchers, and testing their function.

Machine Operation

Site Preparation and Coupling

Advice on selecting storage sites and the procedure for coupling the wrapper to the tractor.

Bale Wrapping and Unloading

Detailed steps for wrapping bales and unloading them from the machine.

Continuous Row Management

Procedures for finishing bale rows and ensuring an airtight seal with plastic film.

Remote Control System

Remote Operation and Controls

How to operate the machine using the remote control and its functions.

Remote Control Programming Procedure

Steps to program or re-associate the remote control with the machine's module.

Maintenance and Storage

Lubrication Schedule and Points

Identifies critical lubrication points and recommended frequency and type of grease.

Cleaning and Preventative Checks

Instructions for cleaning machine parts and performing regular preventative maintenance.

Machine Storage Guidelines

Recommendations for securing and preparing the machine for storage.

Troubleshooting Guide

Common Problems and Solutions

A table listing common issues, their causes, and recommended solutions for the machine.

Hoop Reassembly Instructions

Outer Hoop Assembly Steps

Detailed instructions for correctly assembling the outer hoop sections.

Inner Hoop Assembly Steps

Detailed instructions for correctly assembling the inner hoop components.

Anderson WRAPTOR Specifications

General

Brand	Anderson
Model	WRAPTOR
Category	Farm Equipment
Language	English

Related product manuals

ROUND BALE WRAPPER HYBRID