Why does the plastic film break at normal temperatures on my Anderson Farm Equipment?
If the plastic film breaks at normal temperatures on your Anderson Farm Equipment, make sure the film roll is installed correctly. Check for and remove any debris wrapped around the rolls or in the stretchers. Clean the aluminum rollers with penetrating oil. If the rubber roller is damaged, replace it. Gently sand the spikes if they have become rough.
Why does the plastic film often break in hot weather on my Anderson Farm Equipment?
If the plastic film often breaks in hot weather on your Anderson Farm Equipment, unhook the stretcher springs, as they may be putting too much pressure on the hoop.
Why won't my Anderson Farm Equipment engine start?
If your Anderson Farm Equipment engine doesn't start, several issues could be the cause. First, ensure the fuel valve is open. Next, check if the gas tank is empty and refill it if needed. For Honda engines, a low oil sensor might be activated, so add oil. Also, inspect the spark plug for clogs or defects, and clean or replace it. If the engine is flooded due to fuel valve issues during transport, remove and dry the spark plug, dry the cylinder using the starter crank, then replace the spark plug and try starting again. Finally, make sure there isn't too much oil in the oil pan and adjust the level if necessary.
What to do if the remote starter does not work on my Anderson Farm Equipment?
If the remote starter for your Anderson Farm Equipment isn't working, first, ensure the engine key is in the ON position. If that's not the issue, check the remote control battery for bad contact or a lost charge, and replace it if necessary, then reprogram the remote starter. Also, check the Honda engine fuse and replace it if it has burned out.
What to do if the pusher does not move forward on my Anderson Farm Equipment?
If the pusher on your Anderson Farm Equipment isn't moving forward, the bale may not be correctly placed on the trigger or exerting enough pressure. Rotate the bale a quarter turn and reload it. Also, check the hydraulic oil level and pressure, look for leaks, and add hydraulic oil #32 (or TDH or hydraulic transmission fluid) as needed. Finally, ensure the trigger is properly adjusted.
What to do if the remote control for remote operation does not work on my Anderson Farm Equipment?
If the remote control for remote operation of your Anderson Farm Equipment isn't working, replace the 12 V battery or check its connection. Then, press the right/left direction buttons in alternation to reprogram remote operation. Also, make sure you're not too far from the module; move closer.
What to do if the pusher goes back to its starting position without finishing its trajectory on my Anderson Farm Equipment?
If the pusher on your Anderson Farm Equipment goes back to its starting position before finishing its trajectory, make sure the stopper is correctly positioned for the bale format and fully pushed in. Also, the automatic system spring might be too tight; ensure the spring attachment is vertical or slightly inclined (up to 30°) clockwise and adjust it. Finally, check the oil level and look for leaks to ensure adequate oil pressure, adjusting as needed.
Why is the hoop not turning on my Anderson Farm Equipment?
If the hoop on your Anderson Farm Equipment isn't turning, first, make sure the hoop speed control isn't set to 0; adjust it between 2 and 10. If that's not the problem, check if the drive wheel is sliding on the hoop and tighten the wheel spring. Also, check the oil level and look for leaks to ensure the drive wheel turns properly.
Why are the hoop and the pusher losing speed on my Anderson Farm Equipment?
If the hoop and pusher on your Anderson Farm Equipment are losing speed, check the hydraulic oil level and look for leaks to ensure adequate oil pressure, adjusting as needed.
What to do if the speed control lever is blocked on my Anderson Farm Equipment?
If the speed control lever on your Anderson Farm Equipment is blocked, water infiltration may have caused the interior to rust. Take apart the speed control and lubricate it.
Details of the warranty coverage and duration.
Operator qualifications, safety zones, and warnings.
Clothing, hearing protection, and fire safety.
Safety during repairs, fuel, and road travel.
Leveling, compressing, and wrapping the first bale.
Adjusting film tension for optimal stretch.
Step-by-step guide for system calibration.
Adjusting key operational mechanisms.
Solutions for engine and pusher failures.
Fixing hoop rotation and film issues.
Troubleshooting electronic components.
General| Brand | Anderson |
|---|---|
| Model | ROUND BALE WRAPPER HYBRID |
| Category | Farm Equipment |
| Language | English |
To Next Page
