Anderson 780 SB - User Manual

Questions and Answers

C
Clayton WalkerAug 7, 2025
What to do if the Anderson 780 SB Farm Equipment hydraulic unit engine does not start?
- D
  Destiny HensonAug 7, 2025
  If the engine of your Anderson Farm Equipment hydraulic unit doesn't start, there are several potential causes. First, ensure the fuel valve is open. Next, check that the gas tank isn't empty and refill if needed. Also, verify the engine oil level, adding oil if the low oil sensor is activated. Inspect the spark plug for clogs or defects, cleaning or replacing it as necessary. If the engine is flooded, remove and dry the spark plug, dry the cylinder using the starter crank, then reinstall the spark plug. Finally, check the fuse in the HONDA switch key box and replace it if it's burned out.
Y
ywilliamsAug 14, 2025
Why is the plastic film wrapping unsatisfactory on my Anderson Farm Equipment?
- E
  Elizabeth AcevedoAug 14, 2025
  An unsatisfactory plastic film wrapping on your Anderson Farm Equipment can stem from several issues. The plastic film might break, develop holes, or tear if the roll was damaged initially, so inspect and replace if needed. Obstructions in the film stretcher, like hay, can also cause problems; remove any obstructions and clean the film stretcher, ensuring all rollers turn freely. If the film is too soft from sun exposure, install a cooler roll. Ensure the plastic film roll is installed correctly if the film isn't tight enough on the bale. Also, check the parts of the plastic film stretcher and repair if needed.
B
burgesslaurenAug 22, 2025
What to do if the Anderson Farm Equipment turntable does not turn or turns slowly?
- S
  Scott VangAug 23, 2025
  If the turntable on your Anderson Farm Equipment isn't turning or is moving slowly, the hydraulic oil level may be too low due to loss or lack of oil. Check for any oil leaks or breaks, retighten or repair them as necessary, and add hydraulic oil to the tank.
J
juarezronaldAug 30, 2025
How to fix an Anderson Farm Equipment plastic film cutter that does not work well?
- E
  epriceAug 30, 2025
  If the plastic film cutter on your Anderson Farm Equipment isn't working well, it could be that the plastic film cutter clamp isn't holding onto the end of the plastic film because the rubber stopper moves back too far on its adjustment bolt. Adjust the bolt to fix this. The stopper spring may also need to be more tense.

Summary

Anderson Limited Warranty

Purpose of Warranty

Details the fundamental responsibility of warranty and its intended use.

Warranty Exemptions

Lists conditions that may void the warranty and specific exclusions.

Andersons Responsibilities

Details Anderson Group's responsibilities regarding shipping and freight costs.

Safety Guidelines

Safe Operators

Ensures operators are familiar with procedures and trained for safe operation.

Danger Zone

Defines a security zone around the machine during operation.

Tractor Attachment

Instructions for securely attaching the machine to the tractor for stability.

Dangerous Situations

Highlights hazards like standing on the machine or keeping hands near parts.

Prevention Measures

Recommends appropriate clothing, hearing protection, and fire safety.

Safe Maintenance and Repair

Procedures to follow before performing maintenance or repairs.

Fuel Handling

Safe handling of flammable gasoline for the engine.

Hydraulic Oil Safety

Warns about serious injury from pressurized oil leaks and proper handling.

Road Travel Safety

Guidelines for respecting regulations and securing the machine for transport.

End of Operation

Instructions on closing the engine fuel valve at the end of the day.

General Characteristics and Specifications

Design Features

Details on the use of digital software and laser cutters in manufacturing.

Machine Specifications

Provides exterior dimensions and weight of the bale wrapper.

Adjustment Procedures

Pre-Use Verifications

Checks for hydraulic oil, engine oil, fuel, and air filter before operation.

Installing Plastic Film Roll

Step-by-step guide for removing the old spool and installing a new film roll.

Plastic Film Stretcher Test

Procedure to check the stretch ratio of the plastic film.

Tandem Roller Adjustment

Instructions on adjusting tandem roller spacing for different bale sizes.

Support Roller Adjustment

How to move support rollers to accommodate different bale widths.

Plastic Film Cutter Adjustment

Checking and adjusting the plastic film cutter blade and fingers.

Operating Procedures

Computer Operation

Refers to the separate manual for individual bale wrapper computer controls.

Maintenance Procedures

Grease Gun Lubrication

Details lubrication points and frequency using a grease gun.

Other Lubrication Points

Lubrication of power transmission chains and toothed wheels.

Cleaning and Other Maintenance

Focuses on cleaning the plastic film cutter and rollers, and engine maintenance.

Storage Procedures

Instructions for storing the machine after use, including fuel valve and battery removal.

Troubleshooting and Solutions

Optional Equipment

Front and Rear Stabilizers

Describes the function and benefits of stabilizer options.

Stretch Ratio Gear Modification

Information on modifying gears to change the plastic film stretch ratio.

Double Roll Unit Option

Details the double roll option for applying a double layer of plastic.

Hydraulic Diagram

Electrical Diagram

Anderson 780 SB Specifications

General

Brand	Anderson
Model	780 SB
Category	Farm Equipment
Language	English

Related product manuals

Anderson NutriWrap 780 SB

ROUND BALE WRAPPER HYBRID