How to fix loose forming mold set in anko Vacuum Forming Machines?
If the forming mold set is loose, the hex screws inside the base fixture of the forming mold may be loose. Remove the forming mold set and use a wrench to tighten the hexagon screw inside the base fixture.
Why motor works but no stuffing comes out of anko HLT-700?
If the motor works but no stuffing comes out, it may be because the blade of the stuffing pump is stuck with foreign objects, causing the torque limiter to spin in idle. Remove the foreign object from the choked blade of the stuffing pump. Another possible cause is that the stuffing is not smooth enough, preventing the stuffing propeller from extruding it. Use a torque limiter wrench to tighten the torque limiter.
What to do if the forming mold vibrates on anko Vacuum Forming Machines?
If the forming mold vibrates, it could be because the fixing pin is not fixed properly in the hole. Reinstall the forming mold. Alternatively, excess flour might be obstructing the fixing hole. Clean the excess flour, then reinstall the forming mold.
What to do if finished product jammed on bottom scraper of anko HLT-700 Vacuum Forming Machines?
If the finished product is jammed on the bottom scraper, it could be because the bottom scraper is in excessive contact with the roller. Adjust the bottom scraper to be in reasonable contact with the roller. Another cause could be meat tendon stuck on the bottom scraper; use tools to clean away the meat tendon.
Why is pastry wrapper shrinks in anko Vacuum Forming Machines?
If the pastry wrapper shrinks, it may be because the copper or plastic bushing inside the propeller support is worn out. Replace the worn copper or plastic part. Alternatively, before forming, cut the dough pipe open a little.
What to do if product has missing edges on anko HLT-700?
If the product has missing edges, it could be because the dough extrusion speed is too slow. Increase the dough extrusion feed speed by adjusting the button on the control panel. Alternatively, the dough might be too soft or too hard; water should be 35-50% of flour weight.
Why is dough propeller can not extrude dough in anko HLT-700?
If the dough propeller cannot extrude dough, it may be because the dough is too hard. Ensure the water content is 38-45% of the flour weight. Another possibility is that the machine is connected to the wrong power source; if so, reconnect the correct power source.
Why is sealed edge of finished product damaged when using anko HLT-700 Vacuum Forming Machines?
Damage to the sealed edge of the finished product can be caused by several factors. The dough skin might be too thick; the best dough thickness is two times the thickness of the sealing edge. The dough extrusion speed might be too fast, so try slowing it down. The dough could also be too hard, aim for a water content of 38-45% of the flour weight. Finally, there might be too much stuffing, so do not exceed the maximum recommended amount.
What to do if dry flour does not dust evenly in anko HLT-700 Vacuum Forming Machines?
Uneven dusting can occur if the brush inside the dry flour dusting hopper does not rotate. Tighten the screw of the dust brush. Alternatively, something may be obstructing the dusting holes of the dry flour dusting hopper. Remove the dry flour dusting hopper to clean it.
What to do if my anko HLT-700 does not function?
First, check if the power switch is turned on. If it is on, inspect the circuit board inside the electric box for any loose wires and repair them if necessary. Also, check the circuit breaker and overload protector switch inside the electric box. Finally, ensure that the power source is properly connected and the fuse is not blown; connect the power source or replace the fuse if needed.
Instructions for use are an integral part of the machine and must accompany it throughout its working life.
Verify supplied equipment and accessories are correct and were not affected by transportation.
Details the minimum space required for machine production, cleaning, and maintenance purposes.
Describes the initial cleaning process for parts in contact with food products.
Detailed list of spare parts for the stuffing injection system of the machine.
Comprehensive list of spare parts for the forming mold system component.
Explains the spare parts for the gearbox and dough extrusion system of the machine.
General| Model | HLT-700 |
|---|---|
| Category | Vacuum Forming Machines |
| Max Forming Depth | 200mm |
| Vacuum Pump Power | 1.5 kW |
| Voltage | 380V |
| Power Consumption | 12 kW |
| Machine Weight | 800 kg |
To Next Page