Anritsu MT8821C - 6.3.2.3. Measurement Report for Inter-Frequency; 6.3.2.4. Measurement Report for W-CDMA

243
6.3.2.3. Measurement Report for Inter-Frequency
This chapter describes the UE Report of LTE and Inter-Frequency. In the example, the DL Channel for
Inter-Frequency is set to 2525, Cell ID is set to100 and TAC is set to 000A.
1. [LTE] Execute CALLRFR to initialize the UE Report value.
2. [LTE] Execute NCAINTERFREQ 1,2525 to set leftmost Inter Frequency Cell - DL Channel to 2525.
3. [LTE] Execute NCAINTERCELLID 1,100 to set leftmost Inter Frequency Cell - Cell ID to100.
4. [LTE] Execute NEIGHCELLMEAS INTERFREQ to set Neighbour Cell Measurement to Inter Frequency.
5. [InterFreq] Execute CELLID to set Cell ID to100.
6. [InterFreq] Execute TAC 0000A to set TAC to 000A.
7. [LTE] Connect on Test Mode. (2.3)
8. [LTE] Execute MEASREP ON to request the UE Report.
9. [LTE] Execute MREP_LTE? FLAG and check if the Response is 1 to receive the UE Report for Inter-Frequency.
10. [LTE] Execute MREP_LTE? to read the Cell ID, RSRP, and RSRQ values.
11. To read again, return to Step 10 and continue.
6.3.2.4. Measurement Report for W-CDMA
This chapter describes the UE Report for LTE and W-CDMA. In the example, the DL Channel for W-CDMA is set to
10700 and Primary Scrambling Code is set to to100.
1. [LTE] Execute CALLRFR to initialize the UE Report value.
2. [LTE] Execute NCAWCDMADLUARFCN 1,10700 to set leftmost Inter RAT(W-CDMA) Cell - UARFCN to
10700.
3. [LTE] Execute NCAWCDMACELLID 100 to set Inter RAT(W-CDMA) Cell - Cell ID to 100.
4. [LTE] Execute NEIGHCELLMEAS WCDMA to set Neighbour Cell Measurement to W-CDMA.
5. [W-CDMA] Execute DLCHAN 10700 to set DL Channel to 10700.
6. [W-CDMA] Execute PRISCRCODE 100 to set Primary Scrambling Code to 100.
7. [LTE] Connect on Test Mode. (2.3)
8. [LTE] Execute MEASREP ON to request the UE Report.
9. [LTE] Execute MREP_WCDMA? FLAG and check if the Response is 1 to receive the UE Report for W-CDMA.
10. [LTE] Execute MREP_WCDMA? to read the Cell ID, and RSCP values.
11. To read again, return to Step 10 and continue.
6.3.2.5. Measurement Report for TD-SCDMA
This chapter describes the UE Report of LTE and TD-SCDMA. In the example, the Channel in TD-SCDMA is set to
10054 and Scrambling Code ID is set to 0.
1. [LTE] Execute CALLRFR to initialize the UE Report value.
2. [LTE] Execute NCATDSDLUARFCN 1,10054 to set leftmost Inter RAT(TD-SCDMA) Cell - UARFCN to 10054.
3. [LTE] Execute NCATDSCELLID 0 to set Inter RAT(TD-SCDMA) Cell - Cell ID to 0.
4. [LTE] Execute NEIGHCELLMEAS TDSCDMA to set Neighbour Cell Measurement to TD-SCDMA.
5. [TD-SCDMA] Execute CHAN 10054 to set Channel to 10054.
6. [TD-SCDMA] Execute SCRCODEID 0 to set Scrambling Code ID to 0.
7. [LTE] Connect on Test Mode. (2.3)
8. [LTE] Execute MEASREP ON to request the UE Report.
9. [LTE] Execute MREP_TDSCDMA? FLAG and check if the Response is 1 to receive the UE Report for
TD-SCDMA.
10. [LTE] Execute MREP_TDSCDMA? to read the Cell ID, and RSCP values.
11. To read again, return to Step 10 and continue.