Anritsu MT8821C User Manual

Application Note
Revision History
Ver.
No
Date
Contents
Related product
software version
1.00
May 2015
MT8820C/21C LTE Application Note (Ver. 1.00) is based on
MT8820C LTE Application Note (Ver. 15.00).
Overall: Added MT8821C option model names to MT8820C option
model names
Overall: Added DL CA and UL CA test procedures for MT8821C
Added MT8821C software specification.
MX882012C/42C
Ver. 23.20
MX882112C/42C
Ver. 30.00
2.00
Sep 2015
・1.5.2 Added FDD-TDD 2,3DL/1UL CA, SISO and MIMO to
Supported CA Combination of MT8821C.
・2.4 / 3.6 / 5.3 Added MT8821C connection/RX-measurement/
IP-data-transfer-test procedures for 4DL CA.
・3.3 Added MT8821C measurement procedures for Inter-band UL
CA.
・3.7 Added MT8821C UL Throughput measurement procedure for
SCC.
・7 Added MT8821C VoLTE Echoback test procedure.
・Annex B.2 Added mention of Carrier Leakage Frequency for
measurements on MT8821C intra-band contiguous CC.
・Annex B.3 Added description about optimization of TCP Throughput
by Iperf.
・AnnexB.4 Added maximum rate setting for DL 256QAM.
MX882012C/42C
Ver23.20
MX882112C/42C
Ver30.10
LTE Measurement
Radio Communication Analyzer MT8820C/MT8821C

Anritsu MT8821C Specifications

General

Brand	Anritsu
Model	MT8821C
Category	Measuring Instruments
Language	English

Summary

LTE Measurement Software

1.1. Specifications

The Basic Operations

2.1. LTE Non CA Operations

TRX Measurements (Fundamental Measurements)

3.1. TX Measurements

Detailed TX measurement procedures.

3.1.1. UE Maximum Output Power

Procedure for measuring UE maximum output power.

3.1.3. Maximum Power Reduction (MPR)

Procedure for measuring Maximum Power Reduction (MPR).

3.1.28. Spectrum Emission Mask

3.1.33. Additional Maximum Power Reduction (A-MPR)

3.2. RX Measurements

Detailed RX measurement procedures.

3.2.1. Reference sensitivity level

3.2.1.1. MT8820C Reference Sensitivity

Reference sensitivity level measurement for MT8820C.

3.2.1.2. MT8821C Reference Sensitivity

Reference sensitivity level measurement for MT8821C.

3.2.2. Maximum input level

Procedure for measuring maximum input level.

3.2.3. Spurious emissions

3.3. TX Measurements for CA

3.3.1. TX Measurements for Inter-band CA

TX measurements for inter-band CA.

3.3.1.1. UE Maximum Output Power

3.3.1.2. Maximum Power Reduction (MPR)

MPR measurement for CA.

3.3.1.3. Additional Maximum Power Reduction (A-MPR)

A-MPR measurement.

3.3.2. TX Measurements for Intra-band Contiguous CA

3.3.2.1. UE Maximum Output Power for CA (intra-band contiguous DL CA and UL CA)

UE maximum output power for intra-band contiguous CA.

3.3.2.2. Maximum Power Reduction (MPR) for CA (intra-band contiguous DL CA and UL CA)

MPR measurement for intra-band contiguous CA.

3.3.2.3. Additional Maximum Power Reduction (A-MPR) for CA (intra-band contiguous DL CA and UL CA)

A-MPR measurement for intra-band contiguous CA.

3.3.2.4. Configured UE Transmitted Output Power for CA (intra-band contiguous DL CA and UL CA)

Configured UE transmitted output power for CA.

BAND 13 SUPPLEMENTARY RF CONFORMANCE MEASUREMENT

4.1. PUCCH OVER-PROVISIONING FUNCTIONAL TEST (2.7)

4.2. SPURIOUS EMISSIONS WITH TX GATING (2.9)

IP Data Transfer Test

5.1. IP Data Transfer Test for Non CA (single cell)

IP data transfer test for non-CA single cell.

5.1.1. Connection Diagram

5.1.2. Application Server Connection and Setting

Connecting and setting up the application server.

5.1.4. Initial Condition Setting

5.1.5. Location Registration and Packet Connection

5.1.5.1. IPv4 Location Registration and Packet Connection

5.1.6. TCP/UDP Throughput

TCP/UDP throughput measurement using iperf.

5.1.7. IP Data Transfer Test with Connected DRX

IP data transfer test with connected DRX.

5.1.8. RRC State Transition Test

Testing RRC state transition from Connected to Idle.

5.2. IP Data Transfer Test for 2DL CA

5.2.1. Connection Diagram

5.2.2. Application Server Connection and Setting

5.2.5. Initial Condition Settings

5.3. IP Data Transfer Test for 3/4DL CA

5.3.1. Connection Diagram

5.3.2. Application Server Connection and Setting

5.3.4. Initial Condition Settings

RRM

6.1. 1Port CS Fallback/Redirection

6.1.1. CS Fallback to W-CDMA/Redirection to W-CDMA

6.1.2. CS Fallback to TD-SCDMA/Redirection to TD-SCDMA

6.1.3. CS Fallback to GSM/Redirection to GSM

6.1.4. CS Fallback to CDMA2000/Redirection to CDMA2000

6.1.5. Redirection to 1xEV-DO

6.2. Cell Reselection

Outlines cell reselection and explains the operation procedure.

6.2.1. Cell Selection Criterion

6.2.2. Measurement Rules for Cell Reselection

6.2.3. Inter-RAT Cell Reselection Criteria

6.2.5. Cell Reselection Procedure

Procedure for performing cell reselection.

6.2.5.1. Inter-RAT(TD-SCDMA) Cell Reselection

6.2.5.2. Inter-RAT(W-CDMA) Cell Reselection

6.2.5.3. Inter-RAT(GSM) Cell Reselection

6.3. Measurement Report

6.3.2. Measurement Report Procedure

6.3.2.1. Measurement Report for LTE

6.3.2.3. Measurement Report for Inter-Frequency

6.3.2.4. Measurement Report for W-CDMA

LTE VoLTE Echoback Test (MT8821C Only)

7.1. LTE VoLTE Echoback Test

Testing VoLTE Echoback between MT8821C and UE.

7.1.1. Connection Diagram

7.1.2. Application Server Connection and Setting

7.1.3. Initial Condition Setting