To Next PageTo Next Page
Need help?Do you have a question about the APC 1000VA and is the answer not in the manual?
Inspect UPS upon receipt, check contents, note packaging.
Place UPS where it will be used, ensure sturdy location and proper environmental conditions.
Details the process of attaching mounting rails to the UPS for rack installation.
Step-by-step guide for securely mounting the UPS unit into a server rack.
Guide for installing the battery module and attaching the front bezel.
Instructions for connecting external devices and the power source to the UPS.
Explains Serial and USB ports, interface kits, and cable usage.
Details the indicators and buttons on the front panel for different models.
Explains the function of the 'Online' LED indicator for UPS status.
Explains AVR Trim and AVR Boost LEDs for voltage compensation.
Describes On Battery, Overload, Replace Battery, and Battery Disconnected LEDs.
Details Automatic/Manual Self-Tests and On Battery Operation.
Information on determining UPS run time on battery power.
Sets the interval for UPS self-tests.
Configures UPS ID, battery replacement date, and shutdown delay.
Adjusts UPS reaction to line voltage distortions.
User can mute ongoing alarms or disable existing alarms permanently.
Sets low battery warning intervals and synchronized turn-on delay.
Configures high/low transfer points and output voltage for specific models.
Guidelines for storing the UPS in a cool, dry location with charged batteries.
Procedure for replacing the hot-swappable battery module safely.
Steps to disconnect the battery for shipping compliance with regulations.
Solutions for UPS not turning on or off.
Addresses insufficient backup time and occasional beeps.
Troubleshooting for all LEDs lit, sequential flashing, or all LEDs off.
Solutions for overload conditions and 'Replace Battery' LED.
Addresses site wiring faults and tripped input circuit breakers.
Explains AVR LED indicators and potential voltage problems.
Solves UPS operating on battery and simultaneous LED flashing.
Explains the diagnostic feature for displaying utility voltage.
Steps for obtaining service, including contacting APC and packaging.
Information on how to contact APC for technical support and service.
Lists regulatory approvals and radio frequency warnings for different models.
Details the terms and conditions of the product's limited warranty.
Inspect UPS upon receipt, check contents, note packaging.
Place UPS where it will be used, ensure sturdy location and proper environmental conditions.
Details the process of attaching mounting rails to the UPS for rack installation.
Step-by-step guide for securely mounting the UPS unit into a server rack.
Guide for installing the battery module and attaching the front bezel.
Instructions for connecting external devices and the power source to the UPS.
Explains Serial and USB ports, interface kits, and cable usage.
Details the indicators and buttons on the front panel for different models.
Explains the function of the 'Online' LED indicator for UPS status.
Explains AVR Trim and AVR Boost LEDs for voltage compensation.
Describes On Battery, Overload, Replace Battery, and Battery Disconnected LEDs.
Details Automatic/Manual Self-Tests and On Battery Operation.
Information on determining UPS run time on battery power.
Sets the interval for UPS self-tests.
Configures UPS ID, battery replacement date, and shutdown delay.
Adjusts UPS reaction to line voltage distortions.
User can mute ongoing alarms or disable existing alarms permanently.
Sets low battery warning intervals and synchronized turn-on delay.
Configures high/low transfer points and output voltage for specific models.
Guidelines for storing the UPS in a cool, dry location with charged batteries.
Procedure for replacing the hot-swappable battery module safely.
Steps to disconnect the battery for shipping compliance with regulations.
Solutions for UPS not turning on or off.
Addresses insufficient backup time and occasional beeps.
Troubleshooting for all LEDs lit, sequential flashing, or all LEDs off.
Solutions for overload conditions and 'Replace Battery' LED.
Addresses site wiring faults and tripped input circuit breakers.
Explains AVR LED indicators and potential voltage problems.
Solves UPS operating on battery and simultaneous LED flashing.
Explains the diagnostic feature for displaying utility voltage.
Steps for obtaining service, including contacting APC and packaging.
Information on how to contact APC for technical support and service.
Lists regulatory approvals and radio frequency warnings for different models.
Details the terms and conditions of the product's limited warranty.
General| Output Voltage | 230V |
|---|---|
| Input Voltage | 230V |
| Topology | Line Interactive |
| Waveform | Stepped approximation to a sinewave |
| Output Power | 600W |
| Input Frequency | 50/60Hz |
| Output Frequency | 50/60Hz |
| Battery Type | Lead-acid battery |
| Audible Alarm | Yes |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -15°C to 45°C |
| Humidity | 0-95% non-condensing |
