APC RS 1000 - User Manual

✔
✔
✔
✔
✔
CONNECT TVSS
Back-UPS
®
RS 1000
User’s Manual
Back-UPS
®
RS 1500
1
®
CONTENTS
RJ-45USB
RJ-11RJ-11
2
CONNECT BATTERY CARTRIDGE
4
CONNECT EQUIPMENT / POWER
Monitor
Printer or Scanner
FAX
External Disk or
CD / DVD Drive
10
INSTALL SOFTWARE ON
COMPUTER
There are four status indicators (lights) on the
front panel of the Back-UPS (On Line, On
Battery, Overload, and Replace Battery).
On Line (green) - is lit whenever utility
power is powering the Battery Backup
outlets.
On Battery (yellow) - is lit whenever the
battery of the Back-UPS is powering
equipment connected to the Battery
Backup Outlets.
Four Beeps Every 30 Seconds - this
alarm is sounded whenever the Back-UPS
is running On Battery. Consider saving
work in progress.
Overload (red) - is lit whenever power
demand has exceeded the capacity of the
Back-UPS.
Continuous Tone - this alarm is sounded
whenever the Battery Backup outlets are
overloaded.
Circuit Breaker - the circuit breaker button
located on the rear panel of the Back-UPS
will stick out if an overload condition forces
the Back-UPS to disconnect itself from
utility power. If the button sticks out,
disconnect non-essential equipment. Reset
the circuit breaker by pushing the button
inward.
Replace Battery (red) - is lit whenever the
battery is near the end of its useful life, or
if the battery is not connected (see above).
A battery that is near the end of its useful
life has insufficient run-time and should be
replaced.
Chirps for 1 Minute Every 5 Hours - this
alarm is sounded whenever the battery has
failed the automatic diagnostic test.
Continuous Beeping - this alarm is
sounded whenever a low battery condition
is reached. Battery run-time is very low.
Promptly save any work in progress and
exit all open applications. Shutdown the
operating system, computer and the Back-
UPS.
NOTE: Macintosh Users - for full USB
performance, use OS 9.22 or higher.
If Autoplay is not enabled on the computer,
proceed as follows:
1. On the computer desktop of the display,
double-click on My Computer.
2. Double-click on the CD-ROM drive icon
and follow the on-screen instructions.
11
GROUND
The Back-UPS features a transient
voltage surge-suppression (TVSS)
screw for connecting the ground lead
on additional surge suppression devices
such as network and data line surge
protectors.
Wall
Outlet
Modem/
Phone/Fax
TVSS GND
From Data Line
TVSS
Follow the
on-screen
instructions.
On Line
On Battery
Overload
Replace Battery
w w w .apc.com
®
STATUS INDICATORS AND ALARMS
✔
SERVICE
If the Back-UPS arrived damaged, notify the
carrier.
If the Back-UPS requires service, do not
return it to the dealer. The following steps
should be taken:
1. Consult the Troubleshooting section to
eliminate common problems.
2. If the problem persists, go to http://
www.apc.com/support/.
3. If the problem still persists, contact APC
Technical Support.
4. Have the Back-UPS model number, serial
number and date of purchase available. Be
prepared to troubleshoot the problem with an
APC Technical Support representative. If
this is not successful, APC will issue a
Return Merchandise Authorization (RMA)
number and a shipping address.
7
To Computer USB
Port
CONNECT INTERFACE CABLE
Data Port
BR24BP Batter y Pack
Computer
RJ-45USB
For connection of APC’s optional
external 24-volt battery pack
(BR24BP) to the Back-UPS RS 1000
3
5
Phone Jack
Computer
Modem Port
CONNECT PHONE/MODEM/FAX
TVSS GND
Wal l
Outlet
Wal l
Outlet
Modem/
Phone/Fax
6
CONNECT 10/100 Base-T or VOIP
Network Jack
Computer
Network Port
Note: Allow the Back-UPS to charge for a
full eight (8) hours prior to use.
Press the front panel Power ON/OFF switch
and observe that the following events occur
after pressing and releasing the switch:
• The green On Line indicator flashes.
• The yellow On Battery indicator lights
while a Self-Test is being performed.
• When Self-Test has successfully
completed, only the green On Line
indicator will be lit.
• If the internal battery cartridge is not
connected (see Step 2 above), the green
On Line indicator and red Replace Battery
indicators will light. The Back-UPS will
also emit a chirping sound.
8
SWITCH ON THE BACK-UPS
9
ORIENTATION
10/100 Base-T
VOIP
✘✔✔
Computer
3
OPERATING ENVIRONMENT
32 - 104
o
F (0 - 40
o
C)
✔
✘
24 inches
60 cm
✔
BATTERY
BACKUP
SURGE ONLY
OR
and Back-UPS RS 1500.

Summary

Back-UPS Setup and Operation

Connect Battery Cartridge

Connect the battery cartridge to the Back-UPS unit for power backup functionality.

Operating Environment

Specifies the ideal environmental conditions for operating the Back-UPS unit.

Connect Equipment and Power

Connects external equipment and the AC power source to the Back-UPS.

Connect Phone;Modem;Fax Protection

Connects phone, modem, or fax lines to protect them from surges.

Connect Network Surge Protection

Connects 10/100 Base-T or VOIP network cables to protect against surges.

Connect Interface Cable

Connects interface cables, possibly for optional external battery packs.

Switch On the Back-UPS

Instructions for powering on the Back-UPS unit and observing initial status.

Back-UPS Orientation

Describes the physical placement and orientation of the Back-UPS for optimal use.

Install Management Software

Guides the installation of management software for the Back-UPS on a computer.

Connect TVSS Ground

Connects the TVSS ground for additional surge protection of connected devices.

Status Indicators and Alarms

Explains the meaning of front panel lights and audible alarms on the Back-UPS.

Service and Support

Instructions for handling damaged units and contacting APC technical support.

Troubleshooting and Specifications

Troubleshooting Common Issues

Provides solutions for common problems encountered with the Back-UPS unit.

Technical Specifications

Lists the detailed electrical, physical, and environmental specifications of the Back-UPS.

Transfer Voltage and Sensitivity Adjustment

Guides users on adjusting voltage transfer settings for optimal performance.

Order Replacement Battery Cartridge

Information on how to order a replacement battery cartridge for the unit.

Limited Warranty Information

Details the standard warranty period and procedures for APC products.

APC Contact Information

Provides contact details for APC technical support and worldwide offices.

APC RS 1000 Specifications

General

Nominal Output Voltage	230V
Topology	Line Interactive
Waveform Type	Stepped approximation to a sinewave
Input Voltage Range	180 - 266V
Battery Type	Maintenance-free sealed Lead-Acid battery with suspended electrolyte
Interface Port	USB
Nominal Input Voltage	230V
Input Connection	IEC-320 C14
Frequency	50/60 Hz
Number of Outlets	8
Communication Ports	USB
Output Frequency	50/60 Hz
Input Frequency	50/60 Hz
Data Line Protection	RJ-45 Modem/Fax/DSL protection
Output Power Capacity	600 Watts / 1000 VA
Typical Recharge Time	8 hours